User manual GARDENA WT 1030

[. . . ] To prevent water entering the battery compartment, the Water Timer must only be mounted in a perpendicular position with the sleeve nut pointing upwards. After you have selected the watering program, the Water Timer opens at the selected starting time. To avoid getting wet when operating the Water Timer, connect the hose or turn off the tap before selecting the program. v Only use clear fresh water. G Control knob and OK button : ! " Putting your Water Timer into operation : § ! [. . . ] Press the release button 1 and remove the control unit the housing of the Water Timer. Make sure you exchange the battery at the right time to prevent the Water Timer failing due to a low battery when you are away for longer periods of time. 2 from 5 4 1 2 6 3 6 P z Make sure that the time the battery has been in operation and the time you are planning to be away does not add up to more than a year. 7 G Installing the anti-theft protection (optional) : G To protect your Water Timer against theft, the GARDENA AntiTheft Protection Art. Fasten the bracket 7 to the back of the Water Timer using the screw 8. Set the time on the inner light-grey scale by turning the control knob and confirm the time you have selected by pressing the OK button (e. g. : 10:00 am). 8 2. The Start Time LED flashes. 7 5. Operation Setting the watering program : The Water Timer control unit 2 can be removed. This allows you to set the watering program somewhere other than where the Water Timer is to be used. The time of day and watering starting time are entered to the nearest hour. The program stored in the memory is overwritten. Setting the watering starting time : 3. Set the watering starting time on the inner light-grey scale by turning the control knob and confirm the time you have selected by pressing the OK button (e. g. : 20:00). 3. The Frequency LED flashes. Setting the Watering Cycle : 4. Set the watering cycle on the outer grey scale (Frequency Hours / Days) using the control knob and confirm your selection by press-ing the OK button (e. g. : 12 hour cycle). 1. 8 The Time LED flashes. 4. The Run Time LED flashes. 9 G Setting the Watering Time : 5. Set the watering time on the outer black scale (Run Time Minutes) using the control knob and confirm your selection by pressing the OK button (e. g. : 30 minutes). G Manual watering (ON) : On especially hot days the programmed watering cycle is sometimes insufficient. To activate the set program again, you must reset the watering time to the time originally set. 5. The program you have selected is now active. Bad-weather function (OFF) : Changing the watering time : On hot or cooler days you can change the watering time before the program starts without having to re-enter the time of day, watering starting time or watering cycle. Select the changed watering time on the outer black scale (Run Time Minutes) by turning the control knob. Confirm the watering time you have selected by pressing the OK button. On rainy days the programmed watering cycle is often unnecessary. You can therefore stop the programmed watering cycle (bad-weather function). The valve closes and remains closed, independent of the watering cycle you have set. To reactivate the set program, you must first reset the watering time. The changed watering time is now active. 10 11 G 6. Trouble-Shooting Fault Not able to open the Water Timer manually using "ON / OFF". Data input / changes made while the program was starting or immediately before. [. . . ] If you have any problems with your Water Timer, please contact our Customer Service or return the defective unit together with a short description of the problem directly to one of the GARDENA Service Centres listed on the back of this leaflet. G Product Liability We expressly point out that, in accordance with the product liability law, we are not liable for any damage caused by our units if it is due to improper repair or if parts exchanged are not original GARDENA parts or parts approved by us, and, if the repairs were not carried out by a GARDENA Service Centre or an authorised specialist. The same applies to spare parts and accessories. EU Certificate of Conformity The undersigned GARDENA Kress + Kastner GmbH · Hans-Lorenser-Str. 40 · D-89079 Ulm hereby certifies that, when leaving our factory, the unit indicated below is in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the unit is modified without our approval. [. . . ]