User manual GARDENA 856

[. . . ] To avoid fire hazard, NEVER put the cord under rugs, near heat registers, radiators, stoves, or heaters. · To protect against electrical hazards, DO NOT immerse in water or other liquids. · Close supervision is necessary when any appliance is used by or near children, or disabled persons. · Always unplug the air cleaner before moving it, opening the grill, changing the filters, cleaning, or whenever the air cleaner is not in use. [. . . ] It displays the air quality conditions using a series of LED lights glowing red when high levels of particles are present and green when air quality is improved. Advanced Communication Technology ­ Radio frequency technology sends continuous signals between air cleaner and Galileo® Wireless Air Quality Center. 4 Bionaire®, the Bionaire logo®, Galileo® , the Galileo logoTM and PERMAtechTM are trademarks of The Holmes Group, Inc. or its subsidiary. 13 BAP2000/200105EM1 P. qxd 5/20/05 16:04 Page 9 TROUBLESHOOTING Problem Unit will not operate Solution · Check to make sure the unit is plugged in · Check to make sure the unit is on by pressing the power button · If the Filter Service Indicator is red, the PERMAtechTM filter should be cleaned. · Check to insure nothing is blocking air inlet and filtered air outlet. · Make sure the Galileo® Wireless Air Quality Center is synchronized with the air cleaner by following synchronization instructions. · The Air Cleaner and Galileo® Wireless Air Quality Center can be re-synchronized by holding down the ON/OFF button on both the Air Cleaner and the Galileo® Wireless Air Quality Center at the same time for 5 seconds until you hear a rapid beeping sound. · Chances are there are low levels of airborne particles around the sensor. · Remove the plastic bags from the filters if present. Sensor Control Mode ­ When set to Sensor Control auto mode, the sensor measures your indoor air quality and adjusts the fan speed automatically to provide optimum filtration. It also helps conserve energy by only operating the fan at higher speeds when needed. Remote Operation ­ The function of the Galileo® Wireless Air Quality Center is similar to a remote control. From across the room, you can operate your air cleaner ­ you can change speed settings, turn off appliance or set to sensor control. Decreased airflow Programmable Controls ­ Gives you the flexibility to program your air cleaner to turn on and off at your convenience. You can program the air cleaner to turn on and off at your convenience. NOTE: The Galileo® Wireless Air Quality Center must be used to turn the air cleaner on, set the operating speed and turn air cleaner off in order for the timer to work (Steps 1-3 below). Using the Galileo® Wireless Air Quality Center turn the air cleaner on by pressing the "ON/OFF" button. Then using the Galileo® Wireless Air Quality Center turn the air cleaner off by pressing the "ON/OFF" button. To program the timer press the "TIMER" and "SET" buttons at the same time a) Set the "Timer On" time first: To set the time the air cleaner will come on, press the "TIMER" and "SET" buttons at the same time. b) Press "+" or "-" to set desired hour, then press "SET". c) When a button has not been pressed for a few seconds OR when the "SET" button is pressed again, the minute numbers will begin to flash. d) Press the "+" and "-" to adjust the minutes as indicated above in step 2. e) When a button has not been pressed for a few seconds OR when the "SET" button is pushed again, the timer "ON" will be set and the Timer "OFF" will begin flashing. f) Set the "Timer Off" time second by following instructions in step 4a-e. After completing timer set operation, the "TIMER ON" and programmed time will be displayed. [. . . ] The air cleaner can be operated from either the control panel directly on the air cleaner or the Galileo® Wireless Air Quality Center. To turn the air cleaner on, press the "ON/OFF" button on the Galileo® Wireless Air Quality Center OR press the power button ( ) on the air cleaner. You can select from HIGH ( ), MEDIUM ( ), LOW ( ) or SLEEP ( ) by pressing the "MODE" button on either the air cleaner control panel or the Galileo® Wireless Air Quality Center. The light on the control panel will illuminate letting you know the power is on and at what speed the air cleaner is operating. [. . . ]