User manual GAI-TRONICS COMMANDPLUS DESKTOP CONSOLE

[. . . ] 43004-016E GAI-TRONICS® CORPORATION A HUBBELL COMPANY CommandPLUS Series Desktop Console Operator's Manual GAI-Tronics Corporation 400 E. Mohnton, PA 19540 USA 610-777-1374 800-492-1212 Fax: 610-796-5954 VISIT WWW. GAI-TRONICS. COM FOR PRODUCT LITERATURE AND MANUALS CONFIDENTIALITY NOTICE This manual is provided solely as an operational, installation, and maintenance guide and contains sensitive business and technical information which is confidential and proprietary to GAI-Tronics. GAI-Tronics retains all intellectual property and other rights in or to the information contained herein, and such information may only be used in connection with the operation of your GAI-Tronics product or system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third party. [. . . ] When the talk time is over, the operator releases the appropriate transmit button or if no talk time has been programmed, the console exits paging mode, returns to normal operation and selects the previously selected channel. As discussed earlier, the operator should exercise caution when following a page with a voice transmission to ensure that the correct channel is selected. Therefore, to repeat a stack page, simply reenter paging and begin stacking the pages. As they are stacked, each page that was stacked previously is displayed as long as no other pages have been transmitted. All that is required is to press the LOCK+TRANSMIT key combination to confirm the stacking of each page. No reselection or reentry of pages is required. 25 12/10 Standard Operation CommandPLUS Series Desktop Console Operator's Manual Alert Page It is possible to send out an individual, group or stack page followed by an alert tone. To generate an alert page, select the page or pages to be transmitted. The console generates the page(s) and approximately one second after the last page, begins the generation of the alert tone. The alert can be generated for up to eight seconds as long as the alert tone button is held. Upon releasing the alert tone button or at the end of the alert tone, the console will flash "TALK NOW" at the upper right of the display for a minimum of two seconds. During this time, the microphone is active and voice audio is transmitted over the channel(s). To extend the talk time, press and hold the main TRANSMIT or the TX button on any transmitting channel. When the operator releases the appropriate transmit button or the two seconds time out, the console exits paging mode, returns to normal operation and selects the previously selected channel. As discussed earlier, the operator should exercise caution when following a page with a voice transmission to ensure that the correct channel is selected. Intermediate DTMF Paging Immediate DTMF Paging is slightly different from the other paging formats in that there are no limits on the number of digits that can be transmitted and there are no preset aliases available. To select Immediate DTMF paging, ensure the console is in manual paging mode and that DTMF paging is enabled on the desired channel using CARD Suite. Pressing a digit causes the channel to begin transmission and to transmit the DTMF digit over the channel. It is possible to enter a DTMF A, B, C or D using the LOCK +1, +2, +3 or +4 combination. If the console channel is not currently transmitting, there is a slight delay upon pressing the first digit to allow the base station to begin transmission. It is necessary to press and hold the first digit until it is heard from the select speaker. Upon releasing the button, the channel continues to transmit for approximately two seconds to allow additional digits to be entered. The operator can enter more digits or can begin a voice transmission by pressing and holding the TRANSMIT button. To exit immediate DTMF paging, press the PAGE button or select another type of paging using the MODE button. 12/10 26 CommandPLUS Series Desktop Console Operator's Manual Standard Operation Manual Paging Enable/Disable Use the CARD Suite software application to enable or disable each type of paging (such as DTMF/Immediate DTMF, 2-Tone, 5/6 Tone, and 2805/1500) on each channel. [. . . ] Press the MODE button to save the displayed viewing angle and return to the Clock and Display Set menu. 49 12/10 Console Diagnostics CommandPLUS Series Desktop Console Operator's Manual Setting the Display Brightness The brightness of the console's display can be optimized for the particular location. For example, in a dim environment, the display is more easily read when it is set for a high brightness level. To adjust the display brightness, press 3 from the Clock and Display Set menu to display the screen shown below. To adjust the brightness from this screen, use the SCROLL Up/Down buttons or enter a value from 0 through 7 directly from the numeric keypad. [. . . ]