User manual GAI-TRONICS 13353

[. . . ] 43004-034C GAI-TRONICS® CORPORATION A HUBBELL COMPANY Model 13353, 13363 and 13373 Addressable Amplified Speakers Installation and Operation Manual GAI-Tronics Corporation 400 E. Mohnton, PA 19540 USA 610-777-1374 800-492-1212 Fax: 610-796-5954 VISIT WWW. GAI-TRONICS. COM FOR PRODUCT LITERATURE AND MANUALS Pub. : 43004-034C GAI-TRONICS ® CORPORATION A HUBBELL COMPANY Model 13353, 13363 and 13373 Addressable Amplified Speakers Installation and Operation Manual TABLE OF CONTENTS Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scope of Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 43004-034C Page: 16 of 52 Required Programming Accessories Part No. Description XAC1000A XAC0004A 19101-024 CARD Suite Programming Software CD - Version 4. 3. 0 or newer (needed for all models) Programming Cable (needed for all models) RF Module Programming Kit (needed for Models 13363 and 13373 only) consists of: · Ritron DTX L-Series Programming CD · 9/RTC-PAS Cable · DTXP-PAC Cable Adaptor · 2147C001 9-pin to 25-pin Sub D Adaptor Opening the Addressable Amplified Speaker The Addressable Amplified Speaker must be opened for programming and installation. Remove the speaker from the carton and position on a flat surface with the front of the speaker facing up. Although the front section attaches to the rear section with six Phillips screws, only two screws have been secured during the production process. Lift the front section straight up and flip to the left-hand side of the rear section. Addressable Amplified Speaker. LED Indicators Two LED indicators are located on the speaker amplifier PCBA, but are visible only when the module is opened. The Programming LED indicates when the unit is properly connected to a programming computer using CARD Suite Programming Software. Refer to Figure 18 on page 44 and Figure 19 on page 46 for LED locations. f:\radio products-draft\gtc 43004\43004-034c\43004-034c. doc 05/10 Model 13353, 13363, and 13373 Addressable Amplified Speakers Pub. 43004-034C Page: 17 of 52 Card Suite Software Installation Exit all other programs that are running until the installation is complete. If the "auto-run" feature on your CD-ROM drive is enabled, the CARD Suite menu screen should appear within a few seconds. If the installation does not start up automatically, it can be run from the Start menu. At the prompt, type x:\Setup. exe where x represents the drive letter that is associated with your CD-ROM drive. A CARD Suite icon should appear on the desktop display after successful installation. Connecting the Programming Cable 1. Attach the programming cable to an available COM serial port connector on the computer using the 9-pin adaptor supplied with the cable (CARD Suite supports COM1­COM8). NOTE: If using a USB­to­RS-232 converter, connect the converter to the computer's USB port and then connect the programming cable to the 9-pin mating receptacle on the converter. After opening the Addressable Amplified Speaker (as previously described), plug the programming cable into the programming connector J1 on the speaker amplifier PCBA. Connect a 12­15 V dc power source to the terminal block labeled BATTERY, located on the front section of the Addressable Amplified Speaker assembly or connect the 12­15 V dc power supply provided with the speaker and plug into a 120 V ac source. This illumination verifies the unit is under power and the computer and programming cable are connected properly. f:\radio products-draft\gtc 43004\43004-034c\43004-034c. doc 05/10 Model 13353, 13363, and 13373 Addressable Amplified Speakers Pub. 43004-034C Page: 18 of 52 Programming the Addressable Amplified Speaker Initial Setup and File Creation Run the CARD Suite Programming Software on the PC. The following screen will appear: Select the Addressable Amplified Speaker icon on the left pane of the screen. Any existing speaker archives that are stored in CARD Suite on this PC are shown in the pane on the right side of the screen. These archives can be modified by double-clicking the archive entry in the right pane. To add a new speaker archive, select File New Archive from the tool bar as shown below. [. . . ] Combining this kit with the Model SPK200 Solar Panel Interface Kit and Model RFP7784-108 Solar Panel can provide a completely wireless operation (if RF operation is used). If the application is only temporary, the speaker can easily be "unplugged" from the battery enclosure and relocated or stored. 43003-037 for installation details. f:\radio products-draft\gtc 43004\43004-034c\43004-034c. doc 05/10 Model 13353, 13363, and 13373 Addressable Amplified Speakers Pub. 43004-034C Page: 49 of 52 Model BB133 Battery Backup Kit The Model BB133 Battery Backup Kit provides up to 2 hours of continuous output (full power) if main power is lost or disconnected. [. . . ]