User manual FURUNO SC-120 OPERATORS MANUAL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FURUNO SC-120. We hope that this FURUNO SC-120 user guide will be useful to you.
Manual abstract: user guide FURUNO SC-120OPERATORS MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] SATELLITE COMPASS
SC-120
Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : fax : 0798-65-2111 0798-65-4200
All rights reserved.
Printed in Japan
FIRST EDITION : MAR. OME-72490 ( KAMI ) SC-120
*00080919206* *00080919206*
*00080919206*
*OME72490P10* *OME72490P10*
*OME72490P10*
SAFETY INSTRUCTIONS
Safety Instructions for the Operator Safety Instructions for the Installer
WARNING
Do not open the equipment. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. Do not place liquid-filled containers on the top of the processor unit. [. . . ] 0 0 0 ' E
SOG
0 . 0
kt HDG
2 7 8. 0 °
Position in Latitude, Longitude
Nav data display
3-3
3. OPERATION
Steering display The steering display mainly shows heading, in digital and analog form. The own ship mark points to heading on the bearing scale.
3D
HDG
27 8. 0°
270 280 290
07:54
Bearing scale
Lubber's mark
300
250
260
SOG
0 . 0
kt COG
1 2 3. 4 °
Steering display Compass display The compass display shows heading by compass direction, pitch and roll The compass rose rotates with heading.
3D 23:24:01
HDG
NW W
N
0. 0
°
°
SW NE
Own ship symbol
S E SE
Pitching
PIT
+0
Rolling
ROL
+0°
Compass display ROT (Rate-of-Turn) display The ROT display provides digital and analog indications of rate of turn.
3D
30 20 10 0 10 20 30
ROT scale
ROT
PORT ROT
STBD
1 2 . 2 °/min
ROT display Set and Drift display, Distance Run display Depending on the setting of DISTANCE DISP on the TRIP menu, the Set and Drift display or the Distance Run display is shown. The Set and Drift display requires the Doppler Speed Log DS-80 and it shows current direction and speed.
3D SOG kt
STW kt CURRENT
21. 1 2. 2 22. 2
3 6 . 7 8
nm
DISTANCE
Set and Drift display
Speed and Distance Run display
Set and drift display, distance run display
3-4
3. OPERATION
3. 5
Alarms
The SC-120 can alert you with audio and visual alarms when GPS data and DGPS data are lost. Press the [MENU] key to show the menu.
MAIN MENU
ALARMS MESSAGES GPS SETUP SYS SETUP SOFT VER. OTHERS
SATELLITE DGPS I/O SETUP INST MENU ERASE TRIP MENU
Main menu 2. Choose ALARMS and press the [ENT] key.
ALARMS BUZZER : LONG DGPS : OFF HDG RESTORATION: MAN HDG BACKUP: 5MIN
Alarm menu 3. Press the [ENT] key.
SHORT LONG CONSTANT
Alarm menu, GPS buzzer options 4. SHORT: Two short beeps LONG: Three long beeps CONSTANT: Continuous beep 5. HDG RESTORATION: Choose how to restore GPS signal, automatically or manually. HDG BACKUP: Choose how long to wait before stopping output of heading, when GPS signal is lost.
3-5
3. OPERATION
7.
Press the [ENT] key.
OFF ON
DPGS options
MAN AUTO
HDG RESTORATION options
Alarm menu, DGPS buzzer options 7. For HDG BACKUP, use or on the Omnipad to set time, from 1 to 5 (minutes). Press the [DISP] key to close the menu.
3. 6
Confirming Satellite Status
You can check the receiving condition of each antenna element as follows: 1. Choose SATELLITE and press the [ENT] key.
RX signal level Horizontal bar extends with signal strength. Satellite whose signal strength extends past the first vertical line is used for heading calculation.
PositionNorth fixing status DOP
3D
07 02
N
Elevation angle 5°
10
08
12 01 GPS1
Antenna element no.
DOP 01 1. 5 02 -04 06 05 06 07 04 08 -05 10 -12
Elevation angle 45°
Satellites shown in white on black are used for calculation of heading.
Satellite status display 3. [. . . ] Checksum
A-8
APPENDIX A
VTG - Course over ground and ground speed
COG and SOG obtained by processing the GPS signals. $GPVTG, x. x, T, x. x, M, x. x, N, x. x, K, p*hh<CR><LF> Positioning mode indicator*
Speed, km/h Speed, knots Course degrees magnetic Course degrees true *A = Autonomous, D = Differential, E = estimated(dead reckoning), M = Manual input, S = Simulator, N = Data not valid. The Status field shall be set to V=invalid for all values of Operating Mode except for A=Autonomous and D=Differential. The positioning system Mode indicator and Status field shall not be null fields.
ZDA - Time and date
UTC, day, month, year and local time zone.
$GPZDA. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FURUNO SC-120
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FURUNO SC-120 will begin.