User manual FURUNO MU-200 OPERATORS MANUAL

[. . . ] iii SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv EQUIPMENT LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Installing the Display Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The display unit may fall if only the cover is held. Cover Display Unit Display unit and cover 1 3. Fasten the display unit to the mounting location with eight tapping screws (5X30). However, their length must be at least 30 mm. 501 ±0. 5 483 ±1 440 ±0. 5 422 ±1 346 ±0. 5 226 346 ±0. 5 440 ±0. 5 501 ±0. 5 422 ±1 483 ±1 226 49 113 45 115 100 Unit: mm 45 115 100 Mounting dimensions for landscape orientation Mounting dimensions for portrait orientation Mounting dimensions 4. For the portrait model only, attach the FURUNO logo seal (supplied) at the top left corner. (Remove the logo seal at the bottom left corner. ) 2 49 Unit: mm 113 1. 1. 1 Hood (option) A hood (portrait or landscape) is optionally available. Attach nine sets of Velcro tape to the display unit at the locations shown below, in as straight as possible. Attach in line. Attach in line. Display unit, how to attach Velcro tapes 2. Attach the hood to the display unit. 3 2 WIRING 2. 1 Wiring External Equipment Connect external equipment to the MU-200C by referring to the drawings in this section. For details, see the interconnection diagram on page S-1. General-purpose monitor To use the MU-200C as a general-purpose monitor, connect equipment with a mini D-SUB 15P connector. Nav data is output through the D-SUB 25P connector. FR-2105B Series: PROCESSOR UNIT J2 Mini D-SUB 15P FSV-24: DISPLAY UNIT MONITOR FCV-1200 Series: INTERFACE UNIT RGB OUT FCV-1500 Series: DISPLAY UNIT DISPLAY GP/GD-280/380/680: DISPLAY UNIT EXT VIDEO 100 - 240 VAC Ground Terminal Display unit, rear view, wiring using general-purpose video cables Note: Use the following cable or the equivalent: Mini D-SUB 15P: EVNPS05-50 ft, male-female, (max. 15 m) Manufacturer: BlackBox Japan 4 Connecting FCV-1200 series Using the cables designated below (or equivalent) to connect the FCV-1200 series makes the interface unit of the FCV-1200 series unnecessary. The mini D-SUB 15 P connector cannot be used to connect the FCV-1200 series. Navigator Cable type 06S4078 100 - 240 VAC Ground Terminal FCV-1200 Series: PROCESSOR UNIT CN1 FCV-1200 Series: CONTROL UNIT CONT Cable type MJ-A10SPF0002-015 Display unit, rear view, wiring using specialty cables Notes on wiring · The cover of the D-SUB connector of the cable 06S4078 may be removed to pass the cable through tubing, bulkhead, etc. This allows the cable to be passed through a hole having a diameter of 30 mm. Attach connector SRCN6A13-3S (supplied in installation materials) to the power cable (cable DPYC-1. 5 (Japan Industrial Standard) or equivalent). Sheath Armor 2 cm 3m m · Solder Side Screw 12 Vinyl sheath Armor Conductor S = 1. 5 mm2 B = 1. 56 mm Sectional view of cable DPYC-1. 5 Armor Clamp Tighten set screw 3 Armor Connector Housing Attaching connector SRCN6A13-3S Connect to "1" and "2". 1: AC (L: Live line) 2: AC(N: Neutral line) How to attach connector SRCN6A13-3S; sectional view of power cable DPYC-1. 5 5 · Cable 06S4078 is of waterproof construction, however, the MU-200C is not waterproof (specification IPX0). Therefore, remove rubber cover and fixing metal from the display side of the cable. Remove fixing metal. Remove rubber cover. D-SUB connector 6 3 ADJUSTMENTS Controls for adjustment of the picture are provided on the rear of the display unit. Open the small cover to access the controls. 1 2 POWER 3A S1 S2 S3 S4 Controls for adjustment of picture (remove cover to access) 3 GND 100-240 VAC 50-60 Hz R1 R2 J16 J17 J18 R1 R2 R3 EXTBILL BRILL BRTP G B B J16 1 31 J17 31 J18 3 R3 S1 S2 S3 S4 SEL UP DOWN RESET DATA/VIDEO IN CONT NMEA Rear panel 3. 1 Picture Adjustment Contrast and picture are adjusted with [S1]: Opens OSD (On Screen character Display) menu; selects menu items. The default setting for both is "1-2". S1 J16 1 S2 J17 31 S3 S4 J18 R1 R2 J16 J17 J18 R1 R2 R3 EXTBILL BRILL BRTP G B B 31 3 R3 Jumper blocks S1 S2 S3 S4 SEL UP DOWN RESET 9 4 OPERATION FURUNO LED POWER Switch BRILLIANCE Control Display unit POWER switch: Turns the power on/off. The LED lamp lights in green when the unit is turned on and goes off when the unit is turned off. To turn the MU-200C on and off from the control unit of a video sounder such as the FCV-1200 series, turn on the POWER switch of the MU-200C. Note that with the MU-200C turned on and the FCV-1200 turned off the LED on the MU-200C lights in red. In some instances brilliance is controlled from the equipment connected (for example, FCV-1200 series). LED: Shows display status: Green: Display on Red: Power save 10 5 MAINTENANCE, TROUBLESHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. [. . . ] Connect the power connector (marked with gray arrow) to J1 on the pcb 10P3879: 1, Brown; 3, Orange; 4, Purple, 6, White. Display unit, rear view AP-9 14. Temporarily fasten the cover near the power section/connectors with 10 screws (M3X8). Fasten inner six screws (M3X8) for the cover near power section/connectors. Fasten the remaining four screws for the cover near the power section/connectors. [. . . ]