User manual FURUNO MU-170C OPERATORS MANUAL

[. . . ] OPERATOR'S MANUAL Multi-purpose LCD Display MU-170C IMPORTANT NOTICE · · · · No part of this manual may be copied or reproduced without written permission. If this manual is lost or worn, contact your dealer about replacement. The contents of this manual and equipment specifications are subject to change without notice. The example screens (or illustrations) shown in this manual may not match the screens you see on your display. [. . . ] Fix the above assembly to the mounting location with four hex bolts (M10, dockyard supply). Note: Do not mount the unit where the exhaust or intake vent may be obstructed. Intake vent Exhaust vent 3. Set the display unit to the assembled hanger, and fasten it with four hex bolts (M5x25), spring washers and flat washers. Attach the cosmetic caps and the hard cover to the display unit. Hanger L M10 bolts for fixing (Dockyard supply) Pole Hanger R Flat washer (M10) Spring washer (M10) Hex bolt (M5x25) Spring washer (M5) Flat washer (M5) Hex bolt (M10x30) Hole plug To remove this cosmetic cap, insert fingernail in groove. Desktop mounting 3 1. 2 Remote Controller Setting battery 1. Open the back cover of the remote controller and set two batteries supplied. WARNING Ensure battery polarity is correct. "FCV-1200L") for each "signal" name on the label supplied with the remote controller. Attach the label to the remote controller at the location shown below. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 PIP1 PIP2 PIP3 BRILL + MENU RGB 1 : FCV-1200L RGB2 : DVI : FAR-21X7 series VIDEO1: CCD camera VIDEO2: VIDEO3: Label Remote controller RMC-200 4 2. The items on the RGB1 menu are duplicated on the RGB2 menu. RGB1 RGB2 DVI VIDEO1 640 480 16 44 50 25 31 31 31 7000K OFF OFF FULL 5 VIDEO2 VIDEO3 OSD SYSTEM H_SIZE V_SIZE PHASE CONTRAST H_POSITION V_POSITION R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH DISP MODE SHARPNESS (1 ­ 32) (1 ­ 64) (1 ­ 99) (1 ­ 40) (1 ­ 64) (1 ­ 64) (1 ­ 64) (5500K/6500K/7000K/8000K) (OFF, 1 ­ 10) (OFF, 1 ­ 10) (FULL/EVEN/NORMAL) (1 ­ 10) RGB1 (RGB2) setting menu RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM CONTRAST H_POSITION V_POSITION R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH DISP MODE SHARPNESS 44 25 25 31 31 31 7000K OFF OFF FULL 5 (1 ­ 64) (1 ­ 50) (1 ­ 40) (1 ­ 64) (1 ­ 64) (1 ­ 64) (5500K/6500K/7000K/8000K) (OFF, 1 ­ 10) (OFF, 1 ­ 10) (FULL/EVEN/NORMAL) (1 ­ 10) DVI setting menu 4. Press the MENU key to close the menu. 7 Function Available range Adjusts the image size horizontally. H_SIZE Horizontal size: Narrow () Wide () Variable depending on signal type Adjusts the image size vertically. V_SIZE Vertical size: Narrow () Wide () Adjusts the timing of sampling so that the flicker PHASE** 1-32 disappears and the text is clear. CONTRAST 1-64 Dark () Bright () Moves the image position horizontally. 1-99 (RGB1, 2), H_POSITION To the left () To the right () 1-50 (DVI) Moves the image position vertically. TEMPERATURE 5500K/6500K/7000K/8000K 5500K/6500K/7000K/8000K Warm color Cold color Emphasizes black color. W STRETCH OFF, 1-10 Standard (OFF, ) Bright () Selects the signal resolution. FULL/EVEN/NORMAL* NORMAL: Shows the input signal with same aspect ratio. () *: When inputting VGA, SVGA or XGA, a circle may be displayed as an ellipse because the aspect ratio differs. In this case, select NORMAL from the DISP MODE menu item on the RGB1, 2 or DVI menus. **: If the characters are not clear, adjust PHASE and SHARPNESS. Menu item 8 3. 2 VIDEO Setting VIDEO1, VIDEO2 and VIDEO3 screens can be adjusted independently. Also, the size of the picture-in-picture window can be adjusted at VIDEO1 (2 or 3) setting menu. Picture-in-picture window Picture-in-picture window 1. Same items are contained on VIDEO1, VIDEO2 and VIDEO3 setting menus. RGB1 RGB2 DVI VIDEO1 5 44 31 31 31 7000K OFF OFF VIDEO2 VIDEO3 OSD SYSTEM PIP_SIZE CONTRAST R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH (1 ­ 10) (1 ­ 64) (1 ­ 64) (1 ­ 64) (1 ­ 64) (5500K/6500K/7000K/8000K) (OFF, 1 ­ 10) (OFF, 1 ­ 10) VIDEO1 (2 or 3) setting menu 4. Menu item PIP_SIZE Function Adjusts the size of picture-in-picture window. [. . . ] · Remove dust and dirt from the display unit and LCD with a dry, soft cloth. Do not use chemical cleaners to clean any part of the display unit ­ they can remove paint and markings. · Wipe the LCD carefully to prevent scratching, using tissue paper and an LCD cleaner. To remove dirt or salt deposits, use an LCD cleaner, wiping slowly with tissue paper so as to dissolve the dirt or salt. [. . . ]