User manual FURUNO MU-120C OPERATORS MANUAL

[. . . ] MULTI-PURPOSE LCD DISPLAY MU-120C SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING Do not open the equipment. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. Contact a FURUNO agent for service. WARNING Do not open the cover unless totally familiar with electrical circuits and service manual. Turn off the power at the switchboard before beginning the installation. [. . . ] Insert the display unit to the cutout, and fasten the display unit to the mounting location with four self-tapping screws (5X30, supplied as accessories). However, their lengths must be at least 30 mm. 110 30 Waterproofing: IP20 Cosmetic cap Waterproofing: IPX5 Mounting dimensions 4. Attach the cosmetic caps (supplied as accessories) to the display unit at the locations shown in the drawing above. 2 Desktop mounting The display unit can be mounted on a desktop, using the optional hanger, Type: FP19-00700, Code No. : 001-403-240. Contents of hanger mounting kit Name Hanger Knob bolt Self-tapping screw Type FP19-00701 FP03-09204 5x20 Code No. Fasten the hanger to the mounting location with four self-tapping screws (supplied). Screw knob bolts in hanger, set unit to hanger, and tighten knob bolts. Attach hard cover to protect the LCD. Knob bolt Hanger Desktop mounting 3 1. 2 Remote Controller Write the device name (ex. "FCV-1200L") for each "signal" key on the sticker supplied with the remote controller. Attach the sticker to the remote controller, at the location shown below. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 PIP1 PIP2 PIP3 BRILL + MENU RGB 1 : RGB2 : DVI : VIDEO1: VIDEO2: VIDEO3: Sticker Remote controller RMC-200 WARNING Ensure battery polarity is correct. 4 2 WIRING Connect external equipment to the MU-120C by referring to the drawings below, the table on the next page and the interconnection diagram at the back of this manual. Ground terminal 12-24VDC 12-24 DVC MJ-A3SPF0025-035 (Supplied) VIDEO1 VIDEO2 FAR-21X7 series FEA-2107 DVI-D DVI-D/D SINGLELINK5M (Option) VIDEO3 2. 5C2V or 3C2V (Local supply) CCD camera, Video recorder, etc. RGB1 RGB2 3COX-2P-6C (Option) FCV-1200L series CH-250/S CSH-5L/8L FSV-24/24S/30/30S GP/GD-280/380/680 FR-1510 MARK-3 series FR-21X7 series MODEL1833C series MODEL1833C-BB series Display unit, rear view 5 Port, cable and connectable equipment Port Name 12-24 VDC DVI-D Used cable Name Power cable DVI Cable Type MJ-A3SPF002535 DVI-D/D SINGLELINK5M 3COX-2P-6C 5M 3COX-2P-6C 10M Code No. 000-149-147 000-149-054 Standard/ Option Standard Option Connectable Equipment Power source PC, FAR-21X7 series, FEA-2107 FCV-1200L, CH-250, CH-270, CSH-5L/8L, FSV-24/24S/30/30S, GD-280/380/680, FR1510Mk-3, FR-21X5 series, Model 1833C series, Model 1833C-BB series RGB1 Analog RGB Cable 000-146-500 Option RGB2 000-146-501 Option VIDEO1 Prepare the following cable locally. Connector type: RCA (metal), both ends Cable length: shorter than 10 m 2. 5C2V or 3C2V (Japan Industrial Standard, or the equivalent) coaxial cable (Impedance: 75 ) Cable 3C2V Insulator VIDEO2 Shield Vinyl sheath Video cassette recorder, CCD camera, DVD player VIDEO3 Conductor 2 S = 0. 19 mm = 0. 5 mm Grounding Fasten the ground wire (local supply) between the ground terminal on the display unit and the ship's superstructure. Do Note: Use a "closed-type" lug ( not use an "open-type" lug ( ). 6 3 ADJUSTMENTS Adjust the MU-120C according to the equipment connected. Note that you can adjust the display currently selected, at the DISP selection window. (See section 4. 3. ) 3. 1 RGB/DVI Setting RGB1 and RGB2 screens can be adjusted independently. Otherwise, unwanted image may appear outside of the display area. Note: When the characters are not clear, adjust PHASE and SHARPNESS. 8 3. 2 VIDEO Setting VIDEO1, VIDEO2 and VIDEO3 screens; that is, the picture-in-picture windows can be adjusted as below. Press [] or [] to select VIDEO1, VIDEO2 or VIDEO3 as appropriate. RGB1 RGB2 DVI VIDEO1 VIDE02 VIDE03 OSD SYSTEM PIP_SIZE CONTRAST R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH 5 (1 ­10) 44 (1 ­ 64) 31 (1-64) 31 (1-64) 31 (1 ­ 64) 7000K (5500K/6500K/7000K/8000K) OFF (OFF, 1 ­ 10) OFF (OFF, 1 ­ 10) VIDEO1 (2 or 3) setting menu 3. Menu item PIP_SIZE CONTRAST R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH Function Adjusts the size of picture-in-picture window. Available range 1(25 mmx18mm) 10 (160 mmx129mm) 1-64 1-64 1-64 1-64 5500K/6500K/7000K/8000K OFF, 1-10 OFF, 1-10 Picture-in-picture window Picture-in-picture window 9 3. 3 Menu Window Setting 3. 3. 1 Adjusting the menu window The menu window can be moved and translucentized on the OSD (On Screen Display) menu. Press the [] or [] key to select OSD. RGB1 RGB2 DVI VIDEO1 VIDE02 VIDE03 OSD SYSTEM H_POSITION V_POSITION TRANSLUCENT 12 (1 ­ 22) 23 (1 ­ 23) OFF (OFF/ON) CUSTOM NAME RGB1 = RGB1______ RGB2 = RGB2______ DVI = DVI_______ VIDEO1 = VIDEO1____ VIDEO2 = VIDEO2____ VIDEO3 = VIDEO3____ OSD menu 3. Menu item H_POSITION V_POSITION TRANSLUCENT CUSTOM NAME Function Moves the menu window horizontally. Available range 1-22 (1: left, 22: right) 1-23 (1: up, 23: down) Off, On 10 3. 3. 2 Changing the signal name You can change the signal name which is shown on the DISP or PIP menu, described in the next chapter. [. . . ] Note: The picture-in-picture window can be moved by pressing the arrow keys when a menu window is erased. 17 5 MAINTENANCE, TROUBLESHOOTING WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. 5. 1 Maintenance Routine maintenance Regular maintenance is important for good performance. Check the following on a regular basis to keep the equipment in good operating condition. · Check that the connectors at the rear of the display unit are tightly fastened. · Remove dust and dirt from the display unit and LCD with a dry, soft cloth. [. . . ]