User manual FURUNO GP-7000F

[. . . ] Back COLOR GPS/PLOTTER/SOUNDER GP-7000F The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya 662-8580, JAPAN Telephone : Fax : 0798-65-2111 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : AUG. OME-44291 ( HIMA ) GP-7000F *00014913711* *00014913711* *00014913711* *OME44291B40* *OME44291B40* *OME44291B40* IMPORTANT NOTICE No part of this manual may be copied or reproduced without written permission. The contents of this manual and equipment specifications are subject to change without notice. The example screens (or illustrations) shown in this manual may not match the screens you see on your display. [. . . ] Setting a complete route as destination This method enables you to navigate from the first waypoint of a route. Press the cursor pad to place the cursor at the location not occupied by waypoint. Rotate the [ENTER] knob to choose ROUTE and then push the [ENTER] knob to show the SELECT ROUTE window. SELECT ROUTE ROUTE NAME 1 2 3 4 5 6 7 8 9 10 0001RT 0002RT 0003RT __________ __________ __________ __________ __________ __________ __________ Select route window 4. Rotate the [ENTER] knob to choose a route which you want to set as destination. Setting part of a route as destination You can start the route navigation from any waypoint in a route. Rotate the [ENTER] knob to choose PLOT at the bottom of the screen, and then push the [ENTER] knob. Press the cursor pad to place the cursor on any waypoint which is part of the route you want to set as destination. A line runs between destination selected and own ship's position. Also, range and bearing from own ship's position to destination appear in the data window. You can change the destination in the route by pressing the PREV or NEXT soft key. 6-5 6. NAVIIGATION Skipping route waypoints In some instances you may want to "skip" waypoints while following a route. In the figure below, for example, the vessel has decided to navigate from waypoint 05 to 03, skipping waypoint 04. Waypoint 1 PORT 1 Waypoint 2 Waypoint 3 Waypoint 4 New course line Waypoint 5 Waypoint 6 PORT 2 1. Press the cursor pad to place the cursor on a waypoint which is part of the route. Rotate the [ENTER] knob to choose EDIT at the bottom of screen and then push the [ENTER] knob. Press the [CLEAR] key to close the route list. 6. 4 Cancelling Navigation 1. The confirmation window appears. WARNING Destination is already present. Confirm that "STOP" is selected, and then push the [ENTER] knob. NAVIGATION 6. 5 Affecting the Destination Set at Primary Unit to Secondary When multiple GP-7000 series plotters are connected, the C-LINK feature may be activated to duplicate at the secondary plotter the destination set at the primary plotter. With C-LINK not turned Off, destination may also only be set at the primary plotter. As for secondary units, a "mirror chart card" which mirrors the same area data in the C-MAP MAX chart card in the primary unit, is available. Rotate the [ENTER] knob to choose ADVANCED from the menu bar and then push the [ENTER] knob. Rotate the [ENTER] knob to choose INPUT/OUTPUT and then push the [ENTER] knob. [. . . ] Rotate the [ENTER] knob to choose "RAM menu" and then push the [ENTER] knob. RAM test RAM clear 4. 5. 7. RAM window Rotate the [ENTER] knob to choose "RAM clear" and then push the [ENTER] knob. Press the [POWER/BRILL] key to turn the power off. 11. 8 GPS Cold Start Cold start clears the Almanac (stored in the memory) to receive the latest Almanac from the GPS satellites. When the equipment has not been used for a long time (over one year), execute cold start as shown below to receive the latest Almanac. [. . . ]