User manual FURUNO GP-320B Operators Manual

[. . . ] iii EQUIPMENT LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Qty 1 1 1 Remarks 7P-7P, straight, 10 m MJ-A7SPF/SRMD-100 000-144-534 CP20-01111 NO. 13-QA330 004-365-780 000-803-239 000-803-240 000-806-114 NO. 13-QA310 NO. 13-RC5160 1 1 v (This page intentionally left blank. ) vi 1. MOUNTING Mounting considerations Follow the guidelines below to choose a suitable mounting location for the antenna unit. · The antenna may be mounted three ways: screwed into a pipe (local supply), fixed to a post with the optional mast mounting kit, or screwed into an optional mounting base. For fixing by the post or pipe, it is recommended to use stays to prevent damage to the GPS receiver. · · · The location should be well away from a VHF antenna. Inmarsat transmission will obstruct or prevent reception of the GPS signal. There should be no interfering object within the line-of-sight to the satellites. Objects within line-of-sight to a satellite, for example, a mast, may block reception or prolong acquisition time. Mount the antenna unit as high as possible to keep it free of interfering objects and water spray, which can obstruct reception of the GPS signal if the water freezes. Observe the following minimum separation distances from other antenna units. LOOP ANTENNA WHIP ANTENNA(VHF/UHF) RX WHIP ANTENNA 3m a 1m 1m WHIP ANTENNA(MF/HF) · · INMARSAT ANTENNA 5 m NOT WITHIN INMARSAT BEAM 0. 5 m NOT WITHIN RADAR BEAM * = DISTANCE DEPENDS ON MAST DIAMETER OF 'a'. DIA. OF 'a' DISTANCE (MIN. ) * GPS ANTENNA 4m 4m MAIN MAST 1. 5 m TX ANTENNA(MF/HF) 10 cm 30 cm 1. 5 m 3m Mounting procedure Install the antenna unit by referring to the installation diagram on page D-1. 1 2. NavNet equipment, Multi Display RD-30 and Echo Sounder LS-6100 can be connected directly. For connection to other equipment, use a junction box (local supply) which has seven terminals. If the distance between the antenna unit and the display monitor is more than 10 meters, use the optional cable assy. Up to four extension cables can be connected serially. Connecting to FURUNO NavNet equipment Connect the antenna cable to the DATA1 port on NavNet equipment. Antenna Cable 10 m Cable assy. 50 m Waterproofing connectors If you use the cable assy. (s), waterproof their connectors by wrapping them with vulcanizing tape and then vinyl tape. Bind tape ends with suitable cable-ties. 2 Connecting to Multi Display RD-30 WAAS is not operative in this installation. Antenna Cable 10 m MULTI DISPLAY RD-30 AUX AUX port 12-24 VDC 12-24 VDC IN/OUT IN/OUT port Rear Panel Connecting to Echo Sounder LS-6100 Antenna Cable 10 m ECHO SOUNDER LS-6100 NMEA NMEA XDR 12 VDC POWER POWER 12VDC REAR 3 Connecting to other equipment Remove the connector from the antenna cable and attach crimp-on lugs or similar terminals to the cable's cores. Connect the cores to the junction box as below. Antenna Cable 10 m JUNCTION BOX YELLOW GREEN WHITE BLUE RED BLACK Drain Wire 1 2 3 4 5 6 7 *: RS-422 signal can be received by using current loop. non-NavNet equipment 3 RD-A RS-422* input for radar/plotter 4 RD-B NMEA 0183 Ver. 2. 0 1 TD-A Correction data from GR-80 2 TD-B output in RS-422 format Fuse 0. 5A 12-24 VDC (ship's battery) (Input current: 105-55 mA) Note 1: When connecting FURUNO DGPS beacon receiver GR-80 to this unit, set it as follows: Byte Format, 8-6; First Bit, LSB; Parity Bit, None; Stop Bit, 1; Bit Rate, 8. [. . . ] 12 channels parallel, 12 satellites tracking 1 channel 1575. 42 MHz C/A code, WAAS All in view, 8-state Kalman filter Position Update Interval 1 s 2. I/O INTERFACE 2. 1 2. 2 2. 3 Data format Output data Input data IEC 61162-1 (NMEA 0183 Ver 2. 30) DTM, GGA, ZDA, VTG, GLL, RMC DGPS: RTCM SC-104 Control command 3. ENVIRONMENTAL CONDITIO N 4. 1 4. 2 4. 3 4. 4 Ambient Temperature Relative Humidity Water proofing Vibration -25°C to +70°C 95% at 40°C IEC 60529: IPX6 IEC 60945 5. [. . . ]