User manual FURUNO FCV-667

[. . . ] # # # # # # # # # # # # # # # # # # # # # # # # # &# # <085/#$VKLKDUD0FKR/# 1 L V K L Q R P L \D / # - D S D Q # 7H O H S K R Q H = # 7H O H I D [= # 3 : < ; 0 9 8 0 5 444 # 3:<;09807533# <R X U # / R F D O # $ J H Q W 2 ' H D O H U # $ O O # U L JKW V # U HV HU YHG1 # 3ULQWHG#LQ#-DSDQ# ), 567# (', 7, 21# =# 6(3# 4<<6# # +# = # 1 2 91 # 4 8 / # 4 < < < # +'$0, , # 3 8 % 1 # 1 R 1 # 2 0( 0 5 6 7 8 3 # )&9099:# SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Immediately turn off the power at the switchboard if water leaks into the equipment or something is dropped in the equipment. Fire or electrical shock can result if a liquid spills into the equipment. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. [. . . ] The selected level is shown as SL1, SL2 or SL3 at the top of the screen. Signal level "0" disables this function. 2-8 2. 9 Measuring Depth to a Fish School The VRM (Variable Range Marker) functions to measure the depth to fish schools or other echo. Read the VRM range just above the VRM. 0 VRM (green) 20 39. 8 40 60 49. 6 80 2. 10 A-scope Display This display shows echoes at each transmission with amplitudes and tone proportional to their intensities, on the right 1/4 of the screen. It is useful for estimating the kind of fish school and bottom composition. To turn the A-scope display on or off press the [SIG LEV] and [ALARM] keys together. 0 0. 0 Normal display 10 20 30 32. 3 40 A-scope display 2-9 2. 11 Menu Operation The menu, consisting of the main menu and three system menus, contains less often used functions which do not require frequent adjustment. 2. 11. 1 Menu selection 1. Set the [MODE] switch in the MENU position. NOISE LIMITER OFF 1 2 3 HUE SELECTION 1 (1 - 7) GAIN ADJUST 200KHZ 0 (-20 - +20) GAIN ADJUST 50KHZ 0 (-20 - +20) CLUTTER LEVEL 0* (0 - 3) ZOOM MODE (B. LOCK) M/Z B/L B/Z / -/+ : TO SELECT ITEM, 1/2 : TO SET CONDITION. * A shown when auto mode is active. 2. LOCK) with [w] and then press [w] again. MARKER (VRM) VRM WHT GO TO SYSTEM MENU NO YES / -/+ : TO SELECT ITEM, 2/2 : TO SET CONDITION. 3. To go to the system menu, press [w] to select GO TO SYSTEM MENU and [+] to select YES. You can switch among system menus by selecting MENU and using [+] or [-]. 2-10 ( * SYSTEM MENU [1] *) MENU : DEPTH : SPEED : TEMP : ZOOM MARK : F/A LEVEL : NAV : [1] [2] [3] m ft fa PB kt MPH KPH °C°F OFF ON WEAK MED STRG GRPH DATA (* SYSTEM MENU [2] *) MENU : [1] [2] [3] NAV DSP : OFF L/L R/B CSE FORMAT : NMEA CIF SPD SEL : OFF OWN NMEA TMP SEL : OFF OWN NMEA TMP GRP: OFF LOW HIGH SPD ADJ : +0 % [-50 - +50] TMP ADJ : +0. 0 °F [-20 - +20] (ADJUSTABLE OWN SENSOR ONLY. ) OWN SENSOR SPEED OWN SENSOR TEMPERATURE (* SYSTEM MENU [3] *) MENU : RANGE1 : RANGE2 : RANGE3 : RANGE4 : RANGE5 : RANGE6 : RANGE7 : RANGE8 : ZOOM RANGE: B/L RANGE: [1] [2] [3] 15 (10 - 1000) 30 60 120 200 400 600 1000 X2 X3 X4 X5 10 20 / -/+ : TO SELECT ITEM. : TO SET CONDITION. 0. 0 kt / -/+ °F / -/+ : TO SELECT ITEM. Set the [MODE] switch in any other position to register selection and close the menu. 2. 11. 2 Main menu description Menu item NOISE LIMITER HUE SELECTION GAIN ADJUST (50kHZ, 200KHZ) Description Eliminates noise from other echo sounders and electrical interference. Changing this setting by 10 is equal to changing the GAIN control by 1. If the sensitivity is too low or the auto function does not work properly when the transducer is installed inside the hull, try to adjust the gain here. Eliminates blue dots, which are mainly caused by unclean water, from the screen. Select YES to go to the system menu. CLUTTER LEVEL ZOOM MODE MARKER GO TO SYSTEM MENU 2-11 2. 11. 3 System menu description Menu item System Menu 1 DEPTH SPEED TEMP ZOOM MARK F/A LEVEL Selects unit of depth measurement; meters, feet, fathoms, passi/braza. Selects unit of speed measurement; knots, miles per hour, kilometers per hour. L/L, latitude and longitude position; R/B, Range and bearing to waypoint, CSE, Ship's course. OWN, speed data fed by optional speed sensor; NMEA, speed data fed by position-fixing equipment. OWN, water temperature data fed by optional water temperature sensor; NMEA, water temperature data fed by position-fixing equipment. LOW: Temperature graph scale 30°F to 70°F (0°C to 20°C) HIGH: Temperature graph scale 50°F to 90°F (10°C to 30°C) Offsets speed measured by optional speed sensor. When the water temperature indication appears to be wrong, apply an offset here. [. . . ] When a new sensor is not available, try to turn the water wheel with a finger. If the sensor is normal, the speed indication will be two to three knots when the wheel is turned slowly and seven to eight knots when turned more quickly. As for the water temperature, the water temperature indication should change when you touch the thermosensor. 4. 6 Restoring Default Settings *** OPTION MODE *** 1. The following display appears. [-] : SELF TEST [I] : SET DATA TO DEFAULT [J] : DEMONSTRATION PLEASE HIT ANY KEY. [. . . ]