User manual FURUNO FA-30

[. . . ] For disposal in the USA, refer to the Electronics Industries Alliance (http://www. eiae. org/). i SAFETY INSTRUCTIONS The operator and installer must read the applicable safety instructions before attempting to install or operate the equipment. WARNING CAUTION Warning, Caution Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. Prohibitive Action Mandatory Action Safety instructions for the operator WARNING Do not open the equipment. Immediately turn off the power at the power source if water leaks into the equipment something is dropped into the equipment the equipment is emitting smoke or is on fire the equipment is emitting strange noises WARNING Do not place liquid-filled containers on the top of the equipment. Fire or electrical shock can result if a liquid spills into the equipment. [. . . ] · Fix the unit to the mounting location with 4x20 self-tapping screws (supplied). "A" DETAIL MORE THAN 70 MORE THAN 70 MORE THAN 150 All dimensions in millimeters. 2 1. 3 Whip Antenna Location The location of the AIS VHF-antenna should be carefully considered. Digital communication is more sensitive than analog/voice communication to interference created by reflections in obstructions like masts and booms. It may be necessary to relocate the VHF radiotelephone antenna to minimize interference effects. To minimize interference effects, the following guidelines apply: · The AIS VHF antenna should be placed in an elevated position that is as free as possible with a minimum of 0. 5 meters in the horizontal direction from constructions made of conductive materials. The antenna should not be installed close to any large vertical obstruction. The objective for the AIS VHF antenna is to see the horizon freely through 360 degrees. The AIS VHF antenna should be mounted directly above or below the ship's primary VHF radiotelephone antenna, with no horizontal separation and with a minimum of 2. 8 meters vertical separation. If it is located on the same plane as other antennas, the distance apart should be at least 10 meters. · Install the VHF whip antenna (option) referring to the outline drawing at the back of this manual. Separate this antenna from other VHF radiotelephone antennas as shown below to prevent interference to the FA-30. Whip antenna for AIS Other VHF whip antenna More than 2. 8 m More than 10 m Horizontal separation distance More than 0. 5 m Vertical separation distance Cabling · Use coaxial cable type 5D-2V or the equivalent. · The cable should be kept as short as possible to minimize signal attenuation, and the maximum length is 50 meters. · All outdoor-installed connectors on coaxial cables should be fitted with preventive isolation such as vulcanizing tape to protect against water penetration into the antenna cable. · Coaxial cables should be installed in separate signal cable channels/tubes and at least 10 cm away from power supply cables. The minimum bend radius of the coaxial cable should be 5 times the cable's outer diameter. 3 1. 4 Wiring Connect power source, LAN cable, VHF antenna and ground wire as shown below. VHF WHIP ANTENNA (option) AIS RECEIVER COAXIAL CABLE 5D-2V (local supply) PC, HUB, NAVNET LAN CABLE P5E-4PTX-BL (2 m or 10 m) RS-422 RATING *2 GROUND WIRE IV-1. 25sq NAVNET, SENSOR POWER CABLE (supplied) *1 12-24 VDC RED + BLACK GROUND Switchboard breaker *1 Supply from breaker on switchboard. *2 If COM lines (connection for NavNet, sensor) are not used, tape them to prevent short circuit. 4 Attaching coaxial connector (M-P-5) to coaxial cable The antenna cable (coaxial cable, type 5D-2V) is terminated at the FA-30 with an M-P-5 coaxial connector. Attach the connector to the cable as shown below. Sheath 30 mm 7 mm 2 mm Conductor Insulator Cut conductor here. Contact sleeve Solder here. Braided shield Connection of AIS viewer (FAISPC-MX) The AIS viewer may be connected to the FA-30 directly, or to both FA-30 and NavNet vx2. If change is necessary, click the Data Type drop-down list and choose data type as applicable, among the following choices. IEC61162: Transmit and receive IEC61162 format data via COM port. (P sentences are received but not transmitted. ) IEC61162+ P-sentence: Transmit and receive IEC61162+P sentences format data via COM port. With the radio buttons at RX Speed, choose how RX speed is regulated, Auto or Manual. For manual, choose speed from the drop-down list. Note: Tx speed is fixed at 38400 bps. Click "<<Port Setup" to return to the Port Setup menu. 8 NETWORK setup 9. [. . . ] f ±500 kHz, ±1 MHz, ±2MHz, no modulation ­23 dBm Unwanted freq. f ±5 MHz, ±10 MHz, no modulation ­15 dB PER less than 20% 2. 13 Spurious Emission 9 kHz ­ 1 GHz less than ­57 dBm 1 GHz ­ 4 GHz less than ­47 dBm SP-1 E4443S01A FURUNO 3. 3. 1 FA-30 INTERFACE COM port Input: RS422(38. 4kbps)/IEC61162-1(4800 bps) Output: RS422(38. 4kbps) Input sentences: ACK, ACA, DTM, GBS, GGA, GLL, GNS, HDT, OSD, RMC, VBW, VTG, DSC, DSE, AIQ, ZDA, PFEC, ABM*, BBM*, AIR* Output sentences: ACA, ACS, ALR, VDM, VDO, TXT, ABK*, PFEC 3. 2 NETWORK Ethernet 10/100BASE-T Input sentences: ACK, ACA, DTM, GBS, GGA, GLL, GNS, HDT, OSD, RMC, VBW, VTG, DSC, DSE, AIQ, ZDA, PFEC, ABM*, BBM*, AIR* Output sentences: ACA, ACS, ALR, VDM, VDO, TXT, ABK*, PFEC * ABK sentence sent in response to mis-input of ABM, BBM, AIR. 4. ANTENNA 50 ohm single dipole antenna 5. POWER SUPPLY 12-24 VDC: 1. 2-0. 6 A 6. ENVIRONMENTAL CONDITION -15°C to +55°C 93% at 40°C 6. 1 Ambient Temperature 6. 2 Relative Humidity 6. 3 Waterproofing (IEC 60529) IP20 6. 4 Vibration (IEC 60945 ed. 4) - 2Hz to 5 Hz and up to 13. 2 Hz with an excursion of ±1 mm ±10% (7m/s2 maximum acceleration at 13. 2 Hz ) - above 13. 2 Hz and up to 100 Hz with a constant maximum acceleration of 7 m/s2 7. COATING COLOR N2. 5 SP-2 E4443S01A D-1 D-2 1 WHIP ANTENNA FAB-151D(JAPAN ONLY) 150M-W2VN *2 2 3 4 A COM/POWER J1 2m RED BLK 1 2 P P AIS AIS RECEIVER FA-30 VHF ANT *1 M-P-5 *1 5D-2V, MAX. 50m *1 M-P-5 12-24VDC (+) (-) *4 WHT BLU YEL GRN BRN 1 2 3 4 5 IF-1500AIS EXT. DISPLAY/SENSOR (RS-422/IEC61162-1) J12 DC_P(+) DC_M(-) J7 1 COM_TD-A 2 COM_TD-B 3 COM_RD-A 4 COM_RD-B 5 0V NETWORK RJ45 PC *1 RJ45 LAN CABLE (CAT5) *2 *3 SWITCHING HUB RJ45 P5E-4PTX-BL, 2/10m TX_P 1 HUB-100 P PP B P *1 RJ45 LAN CABLE (CAT5) EXTERNAL DISPLAY TX_N RX_P NC NC RX_N NC (AUTO MDI/MDI-X) NC 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 J1 E_TD_P E_TD_N E_RD_P NC NC E_RD_N NC NC MAIN & PWR 05P0807 GND *1 IV-1. 25sq. C * * *AUTO MDIHUB *COM DRAWN Apr. 12 '07 APPROVED SCALE DWG. No. T. YAMASAKI T. TAKENO MASS kg TYPE FA-30 AIS NAME S-1 NOTE *1: SHIPYARD SUPPLY. [. . . ]