User manual FURUNO FA-150

[. . . ] FA-150 OPERATOR'S MANUAL OPERATOR'S MANUAL UAIS Transponder FA-150 (Elemental Chlorine Free) The paper used in this manual is elemental chlorine free. C Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan FIRST EDITION A2 : DEC. OME-44310 ( DAMI ) FA-150 http://www. furuno. co. jp/ SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Immediately turn off the power at the switchboard if water leaks into the equipment or something is dropped in the equipment. Fire or electrical shock can result if a liquid spills into the equipment. [. . . ] Choose ADRS CAST to send a message to a specific AIS-equipped ship, or BROAD CAST to send a message to all AIS-equipped ships within broadcasting range. For ADRS CAST, "MMSI" is selected; press the ENT key, use the CursorPad to enter MMSI number of the vessel which you want to receive the message, and then press the ENT key. Choose message type: NORMAL (message other than safety) or SAFETY (important navigational or meteorological warning). CHANNEL is chosen; press the ENT key. ALTERNATE BOTH A & B A B 11. Choose SET MSG and press the ENT key. [SET MSG] *: Number of characters available with each message type is as follows: NORMAL message with BROAD-CAST : 156 characters NORMAL message with ADDRESS-CAST : 151 characters SAFETY message with BROAD-CAST : 161 characters SAFETY message with ADDRESS-CAST : 156 characters 01(151)* [DIM]HOLD:CLEAR Number of characters used/available SET MSG screen 15. Choose SEND MSG and then press the ENT key, and the prompt shown right appears. OPERATION The screen shows message status as follows: AIS message status messages and their meanings Message NOW SENDING. (MMSI is additionally shown in case of addressed message. ) Message could not be sent. Message sent successfully, however there is no reply from receiver of message. You tried to send a message while the transponder is awaiting receive confirmation (successful or unsuccessful) for the first-sent message. After confirmation is received, the next sequential message will be sent. 1. 8. 2 Receiving messages How to view a received message When a message is received, the window below appears on the display. To view the contents of the message follow the procedure below. MESSAGE !Choose RX LOG and then press the ENT key. [RX LOG] 03/MAY 13:25 NEW FR : 431099111 N-ABM 28/MAR 03:43 FR: 431099111 S-ABM 22/MAR 18:00 FR: 431099111 N-ABM Date and time message received ("NEW" displayed for unread message) MMSI of sender, type of message N-ABM: Normal, addressed binary S-ABM: Safety, addressed binary N-BBM: Normal, broadcast binary S-BBM: Safety, broadcast binary 1/3[ ] MSG[ENT] QUIT[MENU] Received message log 1-25 1. To view the contents of an unread message, use the CursorPad to choose the message and then press the ENT key. Below is an example of a received message. [RX LOG] I HAVE CHANGED MY COURSE TO 350 DEGREE. QUIT[MENU] Received message example 6. Displaying received messages in a window You may display incoming messages in a window as follows: 1. Use the CursorPad to choose USER SETTINGS and then press the ENT key. [USER SETTINGS] KEY BEEP : ON ALARM BUZZER : ON DISP RCVD MSG : ALL RCVD MSG BUZZ: ON LR MODE : AUTO AUTO SORT : ON CPA/TCPA ALARM USER SETTINGS sub-menu 3. Use the CursorPad to choose DISP RCVD MSG and then press the ENT key. ALL ABM OFF 4. Use the CursorPad to choose which category of receive message you want to display automatically and then press the ENT key. ALL: Display any message upon receipt ABM: Display only addressed binary messages upon their receipt OFF: Disable automatic displaying of incoming messages 5. OPERATION 1. 8. 3 Message logs The FA-150 stores the latest 20 each of transmitted and received messages in respective message logs. When a log becomes full, the oldest message in the log is automatically deleted to make room for the latest. [. . . ] UTC year ALR - Set alarm state --ALR, hhmmss. ss, xxx, A, A, c--c*h<R>F> $ hC< L | | || | | | | | | | +------------- 6 | | | | +----------------- 5 | | | +-------------------- 4 | | +---------------------- 3 | +------------------------- 2 +--------------------------------- 1 1. Checksum AP-18 APPENDIX LRF - See "Input sentences. " LR1 - Long-range reply with destination for function request "A" --LR1, x, xxxxxxxxx, xxxxxxxxx, c--c, c--c, xxxxxxxxx*h<R>F> $ hC< L | | | || | | | | | || | +---- 7 | | | || +---------- 6 | | | | +----------------- 5 | | | +---------------------- 4 | | +------------------------------ 3 | +---------------------------------------- 2 +---------------------------------------------- 1 1. Checksum LR2 - Long-range reply for function requests "B, C, E, and F" --LR2, x, xxxxxxxxx, xxxxxxxx, hhmmss. ss, llll. ll, a, yyyyy. yy, a, x. x, T, x. x, N*h<R>F> $ hC< L | | | | || | | ||| || | | | | || | | | | | | +--- 9 | | | | || | | | | +---+----- 8 | | | | || | | +--+----------- 7 | | | | || +----+----------------- 6 | | | | +---+---------------------------- 5 | | | +------------------------------------------ 4 | | +-------------------------------------------------- 3 | +----------------------------------------------------------- 2 +----------------------------------------------------------------- 1 1. Checksum AP-19 APPENDIX LR3 - Long-range reply for function requests "I, O, P, U and W" --LR3, x, xxxxxxxxx, c--c, xxxxxx, hhmmss. ss, x. x, x. x, x. x, x. x, x. x, x. x*h<R>F> $ hC< L | | | | | | || || || | | | | | | || | | | +---- 12 | | | | | | || | | +------- 11 | | | | | | || | +---------- 10 | | | | | | | | +-------------- 9 | | | | | | | +------------------ 8 | | | | | | +--------------------- 7 | | | | | +------------------------- 6 | | | | +-------------------------------- 5 | | | +---------------------------------------- 4 | | +---------------------------------------------- 3 | +------------------------------------------------------ 2 +------------------------------------------------------------ 1 1. [. . . ]