User manual FUNAI WV806

[. . . ] Please read before using this unit. Owner's Manual DVD/CD Player with Video Cassette Recorder WV806 INSTRUCCIONES EN ESPAÑOL INCLUIDAS. RF cable (WPZ0901TM002) Remote control (NB183UD) with two AA batteries TOLL FREE : 1-800-518-1180 or visit our web site at http://www. funai-corp. com Table of Contents Precautions Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Location and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Avoid the Hazards of Electrical Shock and Fire . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then press [B] to go to next step. or · You can set a program one year in advance. PROGRAM NUMBER 1 DATE ­­/­­ START TIME ­ ­ : ­ ­ ­ ­ END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ 5 Select the desired start time (hour). Then press [B] to go to next step. ONE TIME PROGRAM or 3 Select "ONCE", "DAILY" (Mon-Fri), or "WEEKLY". PROGRAM Then press [B] to go to next step. or NUMBER 1 B ONCE DAILY WEEKLY PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 ­ ­ END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ or ­ 12 ­ EN 6 Select "AM" or "PM". Then press [B] to go to next step. 10 ONE TIME PROGRAM PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 PM END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ AM B PM Press [SUBTITLE/T-SET] to set timer standby mode. SUBTITLE T-SET or · TIMER indicator on the front panel lights up. The unit will change to the DVD mode. Hint 7 8 Repeat the procedure in steps 5 and 6 to set the end time. · To go back one step, press [s] during steps 3 to 9. To Check, Correct or Cancel a Timer Program Select the desired channel. Then press [B] to go to next step. ONE TIME PROGRAM PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 PM END TIME 0 8 : 3 0 PM CHANNEL 16 REC SPEED ­ ­ or · If you have connected the unit to a cable box or satellite box as the connection on page 6, select the VCR to channel 3 or 4 (the RF output channel of the VCR). Leave the cable box or satellite box on for Timer Recording. 9 Select the desired recording speed, then press [CLEAR/C. RESET]. RESET or To cancel a Timer Recording in progress Press [STOP/EJECT C A] on the unit. · To set another program after step 9, press [B]. Then, continue with step 2. Hints for OTR and Timer Recording · Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode, then press [SUBTITLE/T-SET]. · If a tape is not in the unit or does not have the record tab, TIMER indicator on the front panel blinks and Timer Recording cannot be performed. · When Timer Recordings are set, TIMER indicator on the front panel lights up. To use the VCR as usual until the time for the recording, press [SUBTITLE/T-SET] so that TIMER indicator lights off. Select either VCR or DVD mode, then continue with the other features as described in this manual. After an OTR or a Timer Recording has been set, this unit operates as follows: · If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. Press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then press [VCR] to activate the VCR function again. · Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is pressed. · To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then press [VCR] to activate the VCR function again. · The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after you canceled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you operate. When an OTR or a Timer Recording is completed. . . · If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically, and TIMER indicator on the front panel lights to indicate the unit is in the timer standby mode. · TIMER indicator on the front panel flashes if there are no more Timer Recordings on standby. · If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR functions will be unavailable. [. . . ] You MUST select the correct mode on the remote control. 6 Select the current minute. Then press [B] to go to next step. or CLOCK SET MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6 HOUR MINUTE 05 : 40 AM/PM ­­ 4 1 2 Turn on the Unit for the First Time VCR 7 Select "AM" or "PM". or CLOCK SET MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6 HOUR MINUTE 05 : 40 AM/PM P M AM B PM Turn on the TV and set it to channel 3. · If channel 3 has been already occupied for broadcasting, see "RF Output Channel" section. Then press [B] to go to next step. LANGUAGE SELECT 8 To exit the CLOCK SET screen STANDBY-ON or B ENGLISH FRANCAIS ESPAÑOL [ON] ­ 27 ­ EN Quick Use Guide 6 VCR Playback Disc/Tape Button (Alphabetical order) 1 4 7 2 5 8 0 3 6 9 +10 DVD mode VCR mode Before: Turn on the TV and set it to channel 3. · If channel 3 has been already occupied for broadcasting, see "RF Output Channel" section. VCR · To select chapter or title directly. · To select track directly. [. . . ]