User manual FUNAI W6313CA

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. [. . . ] To record on it later, cover the Record safety tab hole with cellophane tape. 1 Press REC/OTR to begin OTR. Change the recording length by pressing REC/OTR repeatedly. REC (Normal recording) OTR(8:00) OTR(0:30) OTR(1:00). . . . . Before recording, make sure: ¡The desired channel is selected by pressing Number on the remote control or CHANNEL (o/p). (If you connected the VCR to a cable box or satellite box as in "CONNECTING TO A TV WITHOUT A/V TERMINALS" on page 13, select channel 3 on your TV, and select the specific INPUT channel assigned by your cable box or your satellite box on the DVD/VCR COMBINATION UNIT. Then, select the channel you want to record with the cable box or the satellite box. In this case, you can ONLY record and view the SAME channel. ) ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. ¡The desired recording speed is selected in SP (standard play) or SLP (super long play) mode by pressing SPEED on the remote control. Tape Speed Type of tape SP mode SLP mode T60 1 hour 3 hours Recording/Playback Time T120 2 hours 6 hours T160 2-2/3 hours 8 hours OTR(7:30) ¡If a tape ends during OTR, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks. To use the VCR again, press T-SET on the remote, or STOP/EJECT on the DVD/VCR COMBINATION UNIT. To use the VCR again, press T-SET on the remote, or STOP/EJECT on the DVD/VCR COMBINATION UNIT. TIMER RECORDING VCR You may set the VCR to start recording while you are away. You can set eight programs to record on specific days, daily or weekly within 1 year period. If you have not yet set the clock, "CLOCK SET" appears. If so, follow the steps [3] and [4] in "CLOCK SET UP" section on page 17. Then, set the timer recording. NORMAL RECORDING VCR 1 Begin the recording by pressing RECORD. The REC Light comes on. ¡If the DVD output mode is selected, you have to switch it to the VCR mode by pressing the VCR on the remote control or the OUTPUT on the VCR. 7) Set the tape speed Press K or L repeatedly for the desired tape speed. Then, press B. ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /12 MON START TIME 07: 30 PM END TIME 08: 30 PM 16 CHANNEL REC SPEED SP SP SLP 2 Select main menu by pressing MENU. To exit, press CLEAR/C. RESET. 3 Select "TIMER PROGRAMMING" by pressing K or L. TIMER RECORDING WILL NOT BE ACTIVATED UNLESS YOU PRESS T-SET. 4 Select the program number you want to check by pressing K or L. ¡The details of the selected program appears on the TV screen. ¡Go to the digit you want to change by pressing B or HINTS FOR TIMER RECORDING VCR ¡If there is a power failure or the VCR is unplugged s. Then, enter correct numbers by pressing o or p. ¡You may cancel the entire program by pressing s while the program number flashes. 5 Press CLEAR/C. RESET to exit. 6 Press T-SET to return to timer stand-by mode. EN 1L25 for more than 30 seconds, the clock setting and all timer settings will be lost. ­ 20 ­ SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. You can not copy a DVD to a videotape. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. (See "RF OUTPUT CHANNEL" on page 13 for the detail). Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. [. . . ] 4] en la página 14 para detalles. CONEXION A UN RECEPTOR CON DESCODIFICADOR DIGITAL DOLBY Por favor, vea la [Fig. 5] en la página 15 para detalles. CONEXION A UN SISTEMA DE AUDIO ANALOGICO Por favor vea la [Fig. 6] en la página 15 para detalles. PREPARACIÓN PREPARACIÓN DE CANAL AUTOMÁTICA VCR 1 Necesita conectar primero la antena o el cable al VCR. Entonces, conecte el enchufe DVD/VCR a una fuente de corriente CA estándar de su vivienda. 4 Seleccione Idioma de Pantalla ("English", "Francais" o "Español") mediante los botones K ó L. [. . . ]