User manual FUNAI W4913LTV

[. . . ] Reset to the Default Setting (Except for PARENTAL Setting) . Setup Connections . 19 20 20 21 21 22 22 23 23 24 24 24 Information VCR Functions Playback . 27 Basic TV Connection Cable TV Antenna signal or Cable TV Antenna (Back of DVD/VCR) signal or (Back of TV) (Back of TV) Disconnect Connect 2 ANT-IN AC outlets ANT-OUT Connect RF cable (supplied) 3 Plug in From DVD/VCR From TV 4 5 Please refer to "Connections" on page 6. Español Information Troubleshooting Guide . . DVD Functions VCR Functions Setup If you need additional operating assistance after reading this owner's manual, please call · Audio/Video cables (WPZ0102TM015 or WPZ0102LTE01) · Owner's Manual (1VMN21067A) Precautions Supplied Accessory Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] ([OUTPUT] on the front panel and [VCR] on the remote control will not function. ) · To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C/A] on the unit, then press [VCR] to activate the VCR function again. · The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after you cancelled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you operate. · If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically, and the TIMER light appears to indicate the unit is in the timer standby mode. · The TIMER light flashes if there are no more Timer Recordings on standby. · If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR function will be unavailable. All the DVD functions are available during OTR, timer standby mode and Timer Recording. If you want to use the DVD player during a Timer Recording or while the TIMER light appears or flashes. Press [DVD] on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. NOTE (for Timer Recording) : · If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost. ­ 13 ­ EN VCR Functions Repeat the procedure in steps 5) and 6) to set the end time. 10 SUBTITLE T-SET · The TIMER light on the front panel appears. The unit will change to the DVD mode. Copying a Video Tape Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. (Back of TV) (Back of another source) DVD/VCR VCR AUDIO IN (Back of Recording DVD/VCR*) or COMPONENT VIDEO OUT AUDIO OUT Y AUDIO OUT L L CB R VIDEO OUT R Connect ANT-OUT 1 ANT-IN DIGITAL AUDIO OUT DVD AUDIO S-VIDEO OUT OUT DVD/VCR COMPONENT VIDEO OUT VCR AUDIO OUT ANT-IN L AUDIO IN Y L CB COAXIAL R CR Connect RF cable (supplied) 2 R VIDEO OUT R VIDEO IN VIDEO VIDEO OUT IN CR ANT-OUT Audio/Video cables (not supplied) 1) 2) 3) 4) *Front input jacks are also available Insert a pre-recorded tape into the playing VCR. · The resume information stays on even when the power is turned off. · Slow forward or reverse speed is different depending on the disc. · Set "STILL MODE" to "FIELD" in the Display menu if pictures in the slow playback mode are blurred. (Refer to pages 20-21. ) Zoom DVD DVD-V Paused and Step-by-Step Playback DVD DVD-V CD 1) Press [ZOOM] during playback. 2) Press [ZOOM] repeatedly to select the required zoom factor: x2, x4 or OFF. x2 x4 Press [PAUSE k] during playback. To continue playback, press [PLAY B]. DVD-V The disc goes forward by one frame each time [PAUSE k] is pressed during the pause mode. To continue playback, press [PLAY B]. 3) Press [K / L / s / B] to slide the zoomed picture across the screen. 4) To exit zoom mode, press [ZOOM] to select OFF. Hint · Zooming function does not work while the disc menu is showing up. · The picture may be distorted when you press [PAUSE k] or [REVh] repeatedly in the zoom mode. · It may take several seconds to slide the zoomed picture. Hint · On DVDs, set "STILL MODE" to "FIELD" in the Display menu if pictures in the pause mode are blurred. (Refer to pages 20-21. ) ­ 15 ­ EN DVD Functions Press [STOP C] during playback. [. . . ] 6)Press [STOP C] to stop playback. Turn on the unit for the first time VCR 5 1 Clock Setup VCR VCR VCR MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see"RF Output Channel" section. or · If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2). 2 POWER Remote Control TV Screen LANGUAGE SELECT B ENGLISH FRANCAIS or ESPAÑOL [ON] 2 or CLOCK SET MONTH DAY 10 / ­­ HOUR MINUTE ­­ : ­­ YEAR ­­­­ AM/PM ­­ Select the current month. 2 1 Installing the Batteries for the Remote Control 2 3 3 3 AUTO SET UP CH 01 or CLOCK SET MONTH DAY 10 / 03 HOUR MINUTE ­­ : ­­ YEAR ­­­­ AM/PM ­­ Select the current day. 3 POWER REW VCR/DVD Switching OPEN/CLOSE Do you connect the cable from the cable box or the satellite box to the unit's ANT-IN jack? YES 4 or CLOCK SET MONTH DAY 10 / 03 HOUR MINUTE ­­ : ­­ YEAR 2005 AM/PM ­­ Yes Press [MENU] POWER SPEED AUDIO OPEN/CLOSE /EJECT OUTPUT VCR F. FWD STOP/EJECT PLAY REC/OTR CHANNEL DVD SKIP H DISC IN STOP PLAY G SKIP to exit. VIDEO AUDIO REV FWD 1 4 2 5 8 0 3 SKIP/CH. NO Select the current year. 6 VCR/TV VCR button DVD button 7 9 SLOW +10 DVD PAUSE DISPLAY VCR No PLAY STOP Please wait for a few minutes. After scanning. . . · The tuner stops on the lowest memorized channel. · You can select only the channels memorized in this unit by using K L [SKIP/CH. [. . . ]