User manual FUNAI VR60WF

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. [. . . ] Use this mode to view letterboxed 4:3 picture content to get a widescreen picture. A 16:9 picture will be magnified similarly, but to a lesser extent. 12 STILL POWER VOL SLEEP INPUT SELECT DISPLAY MUTE SCREEN MODE MENU PREVIOUS STILL STILL INPUT SELECT SLEEP SLEEP DISPLAY 1 1 Press the STILL button. The still mode turns on, and the image displayed on the screen is frozen. Press the SLEEP button. The sleep timer is displayed on the screen. NOTE: NOTE: · When the still mode is on, the message "Still" slowly flashes on the screen. · You cannot turn the still mode on when there is no video signal or when switching between video signals. · If the sleep timer is activated, the remaining time is displayed on the screen. If not activated, "0 minutes" is displayed. 2 Press the SLEEP button to set the time. The SLEEP button switches between the times. 0 minutes 10 minutes 90 minutes 2 Press the STILL button again to turn the Still mode off. NOTE: · You can also press the INPUT SELECT, DISPLAY, SLEEP, VOL K(up) / L(down), MUTE, SCREEN MODE, or MENU buttons to turn the still mode off. The timer starts counting down after the message displaying the set time disappears (after approximately 4 seconds). NOTE: · The remaining time displayed for the sleep timer changes in steps of 1 minute. · To change the set time, repeat the above procedure. 13 OPERATING THE PLASMA DISPLAY You can freeze the image displayed on the screen. You can select the sleep timer. OPERATING THE PLASMA DISPLAY NAVIGATING THE SET UP MENU In the setup menu, you can specify settings for picture adjustment, picture position, language, screen saver, and background. Select "Language" on the MAIN MENU screen with the K / L buttons. NOTE: · Pressing the MENU button cancels the menu. 18 SETTING THE SCREEN SAVER AND THE BACKGROUND COLOR Setting the Screen Saver DISPLAY K MENU PREVIOUS 1 PREVIOUS B SLEEP Select "Screen saver" on the DETAIL screen with the K / L buttons. NOTE: · There are 3 modes for the screen saver; "Off", "Slow", and "Fast". "Slow" moves 1 pixel every 30 minutes, and "Fast" moves 1 pixel every 10 minutes. · When a 480i or 1080i input signal connected to the COMPONENT 2 terminal is displayed, the vertical movement is different. "Slow" moves 2 pixels every 60 minutes, and "Fast" moves 2 pixels every 20 minutes. MENU { L 2 1 2 3 Enter the main menu with the MENU button. Select "Detail" on the MAIN MENU screen with the K / L buttons. The "DETAIL" menu is displayed on the screen. 3 Press the PREVIOUS button to return to the MAIN MENU screen. NOTE: · Pressing the MENU button cancels the menu. Setting the Background Color 1 2 Select "Background" on the DETAIL screen with the K / L buttons. Select "Opaque" or "Translucent" for the background color. 3 Press the PREVIOUS button to return to the MAIN MENU screen. NOTE: · Pressing the MENU button cancels the menu. NOTE: · Press the PREVIOUS button to return to the MAIN MENU. [. . . ] (1054 x 730 x 330 mm) 94. 8 lbs (43 kg) NOTE The specifications and design of this product are subject to change without notice. As an ENERGY STAR ® Partner, our company has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency. registered mark. 29 SPECIFICATIONS REFERENCIA RÁPIDA EN ESPAÑOL Traslado de la unidad principal Debido al considerable peso de la pantalla de plasma, se necesitan dos personas para trasladarla. Ambas personas deben asir la parte superior de la pantalla con una mano y la base de la pantalla con la otra mano. Vea la Figura 1 en la página 4. INSTALACIÓN DE LAS PILAS EN EL CONTROL REMOTO 1 Para retirar la tapa trasera del control remoto, presione la lengüeta hacia abajo con un dedo. 3 Instale la tapa trasera en el control remoto. 2 Instale dos pilas tamaño AA, asegurándose de que la polaridad de las pilas coincida con los símbolos impresos en el interior del control remoto. 30 NOMBRES DE LOS COMPONENTES UNIDAD PRINCIPAL Vea las Figura 2 y Figura 3 en la página 8. 1 2 3 4 5 Botón POWER: Para conectar (ON) o dejar en modo de espera (STANDBY). [. . . ]