User manual FUNAI UNIREMT00001

[. . . ] If it still does not work, try searching for the code (see Searching For Your Code). NOTE: If the device does not have a PWR key, press PLAY. SEARCHING FOR YOUR CODE If your device does not respond to the Catalyst 48 after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Aim the remote control at the the TV and slowly alternate between pressing PWR and TV. NOTE: In the search mode, the Catalyst 48 will send IR codes from its library to the selected device, starting with the most popular code first. [. . . ] PROBLEM: TV/VCR combo does not respond properly. Perform SETUP - 9 - 9 - 2 - VCR - TV SETUP - 9 - 9 - 2 - CBL - TV SETUP - 9 - 9 - 2 - AUX - TV SETUP - 9 - 9 - 2 - TNR - TV SETUP - 9 - 9 - 2 - AMP - TV SETUP - 9 - 9 - 2 - CD - TV SETUP - 9 - 9 - 2 - SAT - TV SETUP - 9 - 9 - 2 - TV - TV SETUP - 9 - 9 - 2 - TV - VCR SETUP - 9 - 9 - 2 - CBL - VCR SETUP - 9 - 9 - 2 - AUX - VCR SETUP - 9 - 9 - 2 - TNR - VCR SETUP - 9 - 9 - 2 - AMP - VCR SETUP - 9 - 9 - 2 - CD - VCR SETUP - 9 - 9 - 2 - SAT - VCR SETUP - 9 - 9 - 2 - VCR - VCR CHANGING VOLUME LOCK The Catalyst 48 is set to control volume of a component through your TV while in the TV, VCR, Cable, or Satellite mode. However, in an Audio mode (i. e. , TNR, AMP, or CD), you have separate control of your audio component's volume. If your TV is not remote controllable, or if you want volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e. g. , through the cable in the TV mode). USER GUIDE PROGRAMMING COMPONENT CONTROL The Catalyst 48 can control up to eight different components. Perform the following instructions for each component you want controlled: NOTE: For TV/VCR Combo control, see the next section. CHECKING THE CODES If you have set up the Catalyst 48 using the Searching For Your Code procedure, you may need to find out which fourdigit code is operating your equipment: For example, to find out which code is operating your TV: 1. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , 3 blinks = 3) and write down the number. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i. e. , AUX, CBL, VCR, SAT, CD, AMP, or TNR) component you are checking. As before, write down each fourdigit code. SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. PROBLEM: CH+ , CH- , and LAST do not work for your RCA TV. INTRODUCTION The CatalystTM 48 Universal Remote Control, developed by Universal Electronics, Inc. for Funai, is the complete solution for all of your remote control requirements. It is designed to operate from four to eight devices with the emphasis on features and functions of your dedicated component(s). The Catalyst 48 requires two (2) fresh AA alkaline batteries (not included) and some easy programming to control your devices. For best results, please read and perform all instructions listed here. [. . . ] Now, whenever you press VOL +, VOL ­, or MUTE on the Catalyst 48, volume will be controlled by your TV. Key Charts The LED (red light) blinks to show that the remote control is working and is sending signals. Use SETUP for all programming sequences. SOLUTION: Try the "Search Method" again after clearing out the device key as follows: Press and hold SETUP until the red light blinks twice, then release. Then press and release the device key to be cleared twice. Continued on back. . . TROUBLESHOOTING (CONT'D) PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. SOLUTION: For power on, these products require programming TV codes. [. . . ]