User manual FUNAI ST4919V

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] Use audio coaxial digital cables available at retail for the audio connections. Front speaker (left) Center speaker Front speaker (right) DC 13. 2V Dolby Digital decoder To COAXIAL DIGITAL AUDIO INPUT jack Surround speaker (right) Subwoofer L AUDIO OUT ANT. L R AUDIO OUT R COAXIAL COAXIAL Surround speaker (left) To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack [Fig. 9] NOTES: · Be sure to turn off the power to all components in the system before connecting another component. · Refer to the Owner's Manuals for the components to be connected to the TV/DVD. · If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode. (See page 27 to set DOLBY DIGITAL to ON. ) · Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion, and may also damage the speakers. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. ­ 13 ­ EN 0C28 TV SECTION SET UP FOR USE You can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/DVD channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box. CHANNEL SET UP FOR THE FIRST TIME TV DELETING (OR ADDING) CHANNEL TV The channels you no longer receive or seldom watch can be deleted from the memory. ­ 15 ­ EN 0C28 TV OPERATION WATCHING A TV PROGRAM TV PICTURE CONTROL TV The TV/DVD's picture controls ­ BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS ­ are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a natural looking image. · TV/DVD power must be turned on. 1 2 Turn on the TV/DVD Press POWER to turn on the TV/DVD. Select the channel number Press CHANNEL(CH. ) K or L to select your desired channel number or press Number on the remote control. Note for using the Number on the remote control: ¡When selecting cable channels which are higher than 99, press +100 first, then, press the last two digits. (Example: to select channel 125, first press "+100" then press "2" and "5"). ¡You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). Remember: ¡If the TV/DVD is connected to a cable box or satellite box, the TV/DVD must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box. 1 Select "PICTURE CONTROL" Press PICTURE on the remote control. 2 Select item you want to adjust Press K or L until desired control is displayed. BRIGHT CONTRAST COLOR TINT SHARPNESS BRIGHT ­PPPPPPPCPPPPPPP+ 3 Adjust sound Press VOLUME(VOL. ) X or Y to adjust the volume. VOLUME 20 3 C CC C C C CCCCCCCCCC Adjust the picture control NOTE: · If you press the CHANNEL(CH. ) o or p in the DVD mode, you can change the TV channels. Even if you turn off the TV/DVD in the DVD mode, when you turn it on again, it will go into the TV mode. Press B or s to adjust to your desired level within 5 seconds. NOTE: · At step 3, the picture adjustment display will disappear from the TV screen after about 5 seconds unless you press any buttons, even though you may not be finished. In this case, repeat from step [1]. DEGAUSSING Magnetism from nearby appliances and speakers might affect the color of the TV picture. [. . . ] does not match the set up This is not a malfunction The camera angle cannot be changed · The DVD does not contain sequences recorded from different camera angles. This is not a malfunction Audio or subtitle language cannot be · The DVD does not contain audio source or subtitles in the selected changed language. "Prohibited icon" appears on the · That operation is prohibited by the player or the disc. No CD reproduction DVD picture dropout DVD picture freeze DVD picture in mosaic No DVD reproduction Problem NOTES: · Some functions are not available in specific modes, but this is not a malfunction. [. . . ]