User manual FUNAI ST413A

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. [. . . ] Then, select the channel you want to record with the cable box or the satellite box. In this case, you can ONLY record and view the SAME channel. ) ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. ¡The desired recording speed is selected in SP (standard play) or SLP (super long play) mode by pressing SPEED on the remote control. Tape Speed Type of tape SP mode SLP mode T60 1 hour 3 hours Recording/Playback Time T120 2 hours 6 hours T160 2-2/3 hours 8 hours OTR(7:30) ¡If a tape ends during OTR, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks. To use the VCR again, press T-SET on the remote, or STOP/EJECT on the DVD/VCR COMBINATION UNIT. TIMER RECORDING VCR You may set the VCR to start recording while you are away. You can set eight programs to record on specific days, daily or weekly within 1 year period. If you have not yet set the clock, "CLOCK SET" appears. If so, follow the steps [3] and [4] in "CLOCK SET UP" section on page 17. Then, set the timer recording. Note ¡You can not copy a DVD to a videotape. NORMAL RECORDING VCR 1 Begin the recording by pressing RECORD. The REC Light comes on. ¡To temporarily stop recording or to resume it, press 1 Insert a tape with its safety tab into the DVD/VCR COMBINATION UNIT. 2 Select main menu by pressing MENU. The set up screen is displayed. TIMER PROGRAMMING PROG 12345678 DATE START TIME END TIME CHANNEL REC SPEED PAUSE. After the VCR has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage. 2 Press STOP when the recording is completed. Note ¡When you wish to watch another program while 4 Set the timer. ¡To go back one step, press s. 1) Set the program number (1-8) PROGRAM NUMBER 4 DATE --/-START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - recording, select desired channel on your TV. Then, enter correct numbers by pressing o or p. ¡You may cancel the entire program by pressing s while the program number flashes. 5 Press CLEAR/C. RESET to exit. 6 Press T-SET to return to timer stand-by mode. EN 1L25 for more than 30 seconds, the clock setting and all timer settings will be lost. ­ 20 ­ SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. You can not copy a DVD to a videotape. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. (See "RF OUTPUT CHANNEL" on page 13 for the detail). Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording VCR] (this unit) 2 Press VCR/TV on the recording VCR. MTS (Multi-Channel Television Sound) SYSTEM VCR When you play a VHS tape, or receive a broadcast on the VCR's tuner, the current status will appear when you press 1)* DISPLAY on the remote control. When you record a MTS broadcast signal, you need to set it to 2)* MTS mode. STOP 12:00AM CH 32 STEREO SAP SP 0:00:00 HIFI DVD/VCR AUDIO OUT VCR AUDIO IN ANT-IN DVD S-VIDEO COMPONENT AUDIO OUT VIDEO OUT OUT Y DIGITAL AUDIO OUT L L R ANT-OUT VIDEO OUT R Cb L COAXIAL VIDEO IN Cr R RF cable (supplied) [TV set] (Use for monitoring) Audio/Video cables (not supplied) 1)* Press MENU and select "TV STEREO" or "SAP" by pressing K or L. ¡Although a program may be broadcast in both stereo OUT IN LEFT RIGHT AUDIO VIDEO ANT in [Playing VCR] (another source) and sub audio, you must select the Recording mode to TV STEREO or SAP before you record a broadcast. 1 Insert a pre-recorded tape into the playing VCR. 2 Insert a tape with a safety tab into the recording VCR. 2)* Press MENU and select "AUDIO OUT" by pressing K or L. ¡While the VCR is set in HIFI stereo mode, HIFI 3 Press SPEED on the recording VCR to select the desired recording speed (SP/SLP). 4 Select the "L1" or "L2"position on the recording VCR. [. . . ] El sintonizador explora y memoriza todos los canales activos de su área. 5 Después de explorar, el sintonizador de detiene en el canal memorizado más bajo. La pantalla de TV retorna al modo TV. 3 Seleccione el Idioma en la pantalla ("INGLÉS", "FRANCÉS" o "ESPAÑOL") presionando K o L. Luego, presione B. ­ 39 ­ SP 1L25 PREPARACIÓN DE RELOJ VCR Ajuste el reloj con precisión para grabación con temporizador automática adecuada. Le sugerimos que usted utilice un TV o estación de radio como su fuente de tiempos. REPRODUCCIÓN DE UN DISCO REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO DVD Para empezar Conecte la alimentación del TV, amplificador y cualquier otro componente que se encuentre conectado al DVD/VCR. [. . . ]