User manual FUNAI SF225A

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] If the color is still not correct, disconnect power cord from AC outlet then reconnect it after 30 minutes. · If there is a power failure of any kind, the unit will retain its memory for this feature. - 15 - EN 9J27 PLAYBACK This TV/VCR will operate with any cassette that has the mark. Push in gently, but continuously, on the center-back of the cassette until it is drawn into the TV/VCR. The TV/VCR will automatically turn on. Window AUTO REPEAT PLAYBACK The TV/VCR has an auto repeat function that allows you to repeat a tape indefinitely without touching the PLAY button. ALL REPEAT: Repeat playback from the beginning to the end of the tape. BLANK REPEAT: Repeat playback from the beginning to a blank part of more than 10 seconds. CORRECT WRONG PRECAUTIONS 1 Select "USER'S SET UP" ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER'S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH · Avoid moisture. Moisture condensation may occur · · · on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your TV/VCR, wait until the tape has warmed to room temperature and the moisture has evaporated. Do not touch the tape with your fingers. Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. 2 Select "ALL" or "BLANK" ­ USER'S SET UP ­ NORMAL PLAYBACK Make sure . . . · TV/VCR power must be turned on. Press the PLAY/K or STOP/L button to point to "REPEAT PLAY". If the tape was originally recorded in SP or LP The tape will automatically stop when the counter mode, the still picture will be black and white in returns to 0:00:00. This is not a fault of the machine, but is a byTIME SEARCH product of the technology involved in producing The Time Search function makes it possible to a TV/VCR with 2 video heads. quickly advance the tape to your desired position · If it is left in the Still mode for more than five minsimply by entering the exact amount of playback utes, the TV/VCR will automatically switch to the time you want to skip. - 17 EN ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER'S SET UP LANGUAGE [ENGLISH] B ZERO RETURN TIME SEARCH 9J27 NOISE CANCEL (in the Still mode) This feature allows you to reposition or reduce the noise lines of a still picture. Press the PAUSE/STILL button so that the noise lines change position on the screen so you can see the picture in its entirety without distracting noise lines. NOTE: This feature can be activated ONLY when viewing a tape recorded in the SLP mode. If the tape was originally recorded in the SP or LP mode, the still picture may revert to black and white in addition to the "noise bars". This is normal. RENTAL PLAYBACK This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes. 1 Select "USER'S SET UP" ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER'S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. VERTICAL HOLD CONTROL In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button. NOTE: If there are video noise lines on the screen, reposition or reduce them. [. . . ] 3) Seleccione "ENGLISH" o "ESPAÑOL" utilizando el botón F. FWD/B o REW/s. 4) Pulse el botón PLAY/K o STOP/L para señalar "AUTOPRESELECCION". El sintonizador explorará y memorizará todos los canales activos de su área. NOTAS: El televisor/videograbadora distingue entre los canales de televisión estándar y los canales de televisor por cable. [. . . ]