User manual FUNAI SC309A

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] Moisture condensation may occur on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your TV/VCR, wait until the tape has warmed to room temperature and the moisture has evaporated. Do not touch the tape with your fingers. Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. 2 Select "ALL" or "BLANK" ­ USER'S SET UP ­ · · · NORMAL PLAYBACK Make sure . . . · TV/VCR power must be turned on. Press the PLAY/K or STOP/L button to point to "REPEAT PLAY". Press the F. FWD/B or REW/s button repeatedly until your desired selection [ALL] or [BLANK] appears. RENTAL B REPEAT PLAY AUTO RETURN [OFF] [ALL] [OFF] 3 Exit the Repeat Play setting Press the MENU button on the remote control to return to the TV mode. 1 Insert a prerecorded tape If the erase-protection tab has been removed, the TV/VCR will start playback automatically. 4 Start playback 2 To begin playback PLAY B Press the PLAY button. Press the PLAY button to start the Repeat Play. · Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/VCR. · If the Rental mode is set [ON], the "RENTAL PLAY B" display has priority. 3 To stop playback STOP TO CANCEL THE REPEAT PLAY MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. If there is a power failure of any kind, the unit will retain its memory for this feature. - 16 EN 9J27 Press the STOP button when playback is completed. SEARCH PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. VERTICAL HOLD CONTROL In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button. NOTE: If there are video noise lines on the screen, reposition or reduce them. Refer to "NOISE CANCEL". 2 Set "RENTAL" to [ON] ­ USER'S SET UP ­ Press the PLAY/K or STOP/L button to point to "RENTAL". Press the F. FWD/B or REW/s button until [ON] appears. B RENTAL REPEAT PLAY AUTO RETURN [ON] [OFF] [OFF] 3 Exit the Rental setting PICTURE CONTROLS TRACKING ADJUSTMENT Press the MENU button on the remote control to return to the TV mode. · Tracking adjustment will be set automatically · 4 Start playback (Digital Tracking function) when you start playback. However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHANNEL K or L button until the streaks disappear. To return to the DTR function, stop the tape once and start playback again. Press the PLAY button to start playback. · Once you select the Rental mode, it stays in effect even after you turn off the TV/VCR. TO CANCEL THE RENTAL MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. If there is a power failure of any kind, the unit will retain its memory for this feature. RECORDING TWO DIFFERENT TAPE SPEEDS Before recording, select the tape speed from : SP mode (Standard Play) or SLP mode (Super Long Play). The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each mode. [. . . ] Si desea recuperar canales seleccionados, usted podrá seleccionar directamente el canal deseado con los botones numerados del mando a distancia o con los botones CHANNEL K o L. AJUSTE DEL RELOJ Cerciórese. . . · La alimentación del televisor/videograbadora deberá estar conectada. En el ejemplo de abajo, el reloj va a ajustarse así: FECHA: 1 de mayo de 2000 HORA: 5:40 PM 1) Pulse el botón MENU en el mando a distancia. Pulse el botón PLAY/K o STOP/L para indicar "AJUSTE RELOJ". [. . . ]