User manual FUNAI FV2161

[. . . ] Read instructions-All the safety and operating instructions should be read before the appliance is operated. Retain Instructions-The safety and operating instructions should be retained for future reference. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. Follow Instructions-All operating and use instructions should be followed. [. . . ] · TV/VCR power must be turned on. · gory and change it to [BLOCK], the higher rating will change to [BLOCK] automatically. When you change "TV-Y" to [VIEW], the all ratings will change to [VIEW] automatically. Rating Category Explanations Appropriate for all children Appropriate for children seven and older General Audience Parental Guidance suggested. Unsuitable for children under 14 Mature audience only 1 Select "V-CHIP SET UP" ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER'S SET UP B V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH Selection TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "V-CHIP SET UP". Then press the F. FWD/B button. 2 Select "MPAA RATING" B ­ V-CHIP SET UP ­ TV RATING MPAA RATING Press the PLAY/K or STOP/L button to point to "MPAA RATING". Then press the F. FWD/B button. When you select TV-Y7, TV-PG, TV-14 or TV-MA and you press the F. FWD/B button, the sub-ratings will appear on the TV screen. If you select the rating category (example: TV-PG) and change it to [BLOCK] or [VIEW], the sub-ratings (example: V for Violence) will change to [BLOCK] or [VIEW] automatically. You can set the sub-ratings to [BLOCK] or [VIEW] individually when the rating category is set to [BLOCK]. · When you select [TV-Y7]: Press the STOP/L or PLAY/K button to select "FV" (Fantasy Violence). · When you select [TV-PG], [TV-14] or [TV-MA]: Press the STOP/L or PLAY/K button to select "D"(Suggestive Dialog), "L"(Coarse Language), "S"(Sexual Situation) or "V"(Violence). (in the SP / LP / SLP modes) 2) Press it again and the TV/VCR will now search in super high speed. (in the LP / SLP modes only) NOTE: Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture may revert to Black and White. 3) Press the PLAY/K button to return to normal speed. NOTES: · Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time. In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction. 1 2 Insert a tape. Select "TIME SEARCH" mode Press the TIME SEARCH button (with each push it will increase by 10 minute). 3 Enter your desired time ZERO RETURN This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding. NOTE: Zero Return WILL NOT work on a blank tape or a blank portion of a tape. Press the PLAY/K or STOP/L button until your desired time appears. (Example: "2:50" stands for 2 hours 50 minutes) If you wish to cancel the Time Search at this point, press the MENU button on the remote control. TIME SEARCH 2 : 50 4 Begin Time Search 1 Stop a tape at your desired point Rewind or fast forward the tape to the beginning point at which you want to review. By pressing the REW/s or F. FWD/B button, the TV/VCR will rewind or fast forward to the specified point. When 0:00 is reached, the tape will start playback automatically. 2 3 Reset the counter to 0:00:00 Press the COUNTER RESET button repeatedly. Begin recording or playback TO CANCEL THE TIME SEARCH at this point Press the STOP/EJECT button on the TV/VCR or the remote control. This will delete the selected time. Press the RECORD or PLAY button. Press the STOP button when recording or playback is completed. STILL PICTURE 4 To activate "ZERO RETURN" mode Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "ZERO RETURN". [. . . ] Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa MENU en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta. 1 Seleccione "AJUSTE DE CANAL" ­MENU­ COMO PROGRAMAR CONTROL DE IMAGEN AJUSTE RELOJ B AJUSTE DE CANAL AJUSTE DE USER AJUSTE DE V-CHIP IDIOMA [ESPAÑOL]` TITULO [OFF] RETORNO A CERO BUSQUEDA DE HORA Pulse el botón MENU en el mando a distancia. Pulse el botón PLAY/K o el botón STOP/L para señalar "AJUSTE DE CANAL". A continuación, pulse el botón F. FWD/B. 2 Empiece el prefijado automático ­ AJUSTE DE CANAL ­ AGREGAR/BORRAR (CATV) Pulse el botón PLAY/K o STOP/L para señalar "AUTOPROGRAMACION DE CA". [. . . ]