User manual FUNAI FTR9TC

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] After rewinding finishes, the unit will eject the tape and turn itself off. This function is operative when Repeat Play is set to the [OFF] position. The tape will not auto-rewind during timer recording or One Touch Recording. - 29 - EN 1C29 RECORDING Make sure . . . · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) NOTES: · This unit will ONLY record and view the same channel. · This unit cannot record the contents from the built-in DVD. NORMAL RECORDING TV/VCR You can ONLY watch the same TV program that is being recorded. SKIPPING UNWANTED SCENES DURING RECORDING TV/VCR Press the PAUSE button to temporarily stop recording. NOTES: · After 5 minutes, the unit will automatically switch to the Recording mode to prevent tape damage. · If "CLOSED CAPTION (ON)" is selected, the OnScreen Display will appear for 5 seconds, then disappear. PAUSE SP 1 Select the channel to be recorded Press the number buttons on the CH 10 remote control or the CHANNEL button K or L. Remember: If the unit is connected to a cable box or satellite box, the unit must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). SP 3 Begin recording REC Press the RECORD button. SP 4 Stop recording Press the STOP button when recording is completed. - 30 - EN 1C29 OTR (One Touch Recording) TV/VCR This function enables you to set a recording length simply by pressing the REC/OTR button on the unit. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) NOTES: · You cannot start OTR with the remote control. · If a cable box or satellite box is connected with the unit you will be limited to record only one channel, and the channel selector on the unit must be selected to the output channel of the boxes CH 3 or CH 4 and then the actual channel to be recorded must be selected on the boxes. · Clock must be set to the correct time and date before setting the timer. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) · The channel you want to record is properly set in advance. There is a chance that a program will not be recorded, when programs overlap; · The program with an earlier start has priority. · Once the earliest program finishes, the overlapping programs will begin recording in sequence. · The illustration below demonstrates the sequence of recordings. Program 1 10:00AM - 11:00AM Program 2 9:00AM - 10:00AM Program 3 9:30AM - 12:00PM Recording Sequence Program 1 10:00AM-11:00AM Program 2 9:00AM-10:00AM Program 3 9:30AM-12:00PM 9:00AM 10:00AM 11:00AM 12:00PM 1 Select "TIMER PROGRAMMING" - TV/VCR SETUP B TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH Press the SETUP button on the remote control. Confirm "TIMER PROGRAMMING" is pointed by pressing the Arrow button K, then press the ENTER button. · If you have not yet set the clock, "MANUAL CLOCK SET" appears. Then set the timer recording. 2 Select your desired program ­ TIMER PROGRAMMING ­ CH DATE B-/-/-/-/-/-/-/-/BEGIN END -:-:-:-:-:-:-:-:-:- -:- -:- -:- -:- -:- -:- -:- - position (1~8) Press the Arrow button K or L to select the desired program position. [. . . ] · El televisor/videograbadora/DVD puede reconocer los canales de TV para que sean canales de TV de antena de cable con las condiciones de recepción. En este caso, pruebe nuevamente con el prefijado automático en las condiciones de recepción fina. componentes, si es necesario. 1 Presione el botón POWER. 2 Presione el botón OPEN/CLOSE para abrir la bandeja de carga del disco. 3 Ponga el disco deseado en la bandeja, con la etiqueta hacia arriba. 4 Presione el botón PLAY. ¡La bandeja se cerrará automáticamente y la repro- AJUSTE DEL RELOJ TV/VCR Cerciórese. . . · La alimentación del televisor/videograbadora/DVD deberá estar conectada. [. . . ]