User manual FUNAI B5300

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. [. . . ] The set up screen is displayed. TIMER PROGRAMMING PROG 12345678 DATE START TIME END TIME CHANNEL REC SPEED PAUSE. After the VCR has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage. 2 Press STOP when the recording is completed. Note ¡When you wish to watch another program while 4 Set the timer. ¡To go back one step, press s. 1) Set the program number (1-8) Program number which is not set up flashes. Then, press B. PROGRAM NUMBER 4 DATE --/-START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - recording, select desired channel on your TV. ¡This is not possible when using a cable box or satellite box. ­ 19 ­ EN 1L25 2) Set the frequency of the recording For once: Press K or L to point to "ONCE". For daily (Monday~Friday): Press K or L to point to "DAILY". Then, press B. PROGRAM NUMBER 4 ONCE DAILY WEEKLY ¡If a tape ends during TIMER RECORDING, the 3) Set the date First, press K or L for the month. Then, press B. ONE TIME PROGRAM PROGRAM NUMBER 4 DATE --/-START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks. ¡If a tape is not in the VCR or does not have a safety tab, the TIMER REC light flashes and timer recording will not operate. ¡When all timer recordings are finished, the TIMER REC light will flash. To use the VCR again as usual, press T-SET to disable the flashing TIMER REC light, then press VCR/TV to select the VCR position. ¡When you use the A/V input jacks on the back of the DVD/VCR, select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons (o/p). ¡When you use the A/V input jacks on the front of the DVD/VCR, select "L2" position by pressing [0], [0], [2] on the remote control or the CHANNEL buttons (o/p). 5 Press REC/OTR on the recording VCR. ¡For best results during dubbing, use the VCR's front panel controls whenever possible. ¡Always use video-quality shielded cables with RCA-type connectors. ¡You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR. ­ 21 ­ EN 1L25 AUTO REWIND When a tape reaches the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and switch itself off. ¡The VCR will not rewind the tape automatically during timer recording or One Touch Recording. REAL TIME TAPE COUNTER ¡This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change during blank portions of the tape. ) ¡The indication will appear when the tape is rewound further than "0:00:00" on the tape counter. PLAYING A DISC BASIC PLAYBACK DVD-V Getting started ¡Turn on the power of the TV, amplifier and any other CD components which are connected to the DVD. ¡Make sure the TV and audio receiver (commercially available) are set to the correct channel. ¡Select DVD mode by pressing DVD on the remote control or OUTPUT on the front panel. Notes ¡A "prohibited icon" may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc. ¡With DVDs that use titles for playback program signals, playback may start from the second title, or it may skip these titles. ¡During the playback of a two layered disc, pictures may stop for a moment. [. . . ] Después, presione B. otro componente que esté conectado al DVD. ¡Asegúrese de que la televisión y el receptor de 3 Ajuste el reloj. 1) Ajuste el mes Presione el botón o ó p repetidamente. Entonces, presione B. 2) Ajuste el d a audio (disponible en los comercios) esté ajustado en el canal correcto. ¡Seleccione el modo DVD presionando el botón DVD que está situado en el mando a distancia o el botón output situado en el panel frontal. 1 Presione el botón POWER. 2 Presione el botón OPEN/CLOSE para abrir la bandeja de carga para discos. Presione el botón o ó p repetidamente. [. . . ]