User manual FUNAI 2970LV

[. . . ] For example, to have the Catalyst 48 control a TV, a Cable Converter, and two VCRs, you will need to re-assign the unused AUX key to operate the second VCR as follows: 1. On the Catalyst 48, press and hold SETUP until the LED blinks twice, then release SETUP. To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components: AUX as 2nd TV key: AUX as 2nd VCR key: AUX as 2nd CBL key: AUX as 2nd TNR key: AUX as 2nd AMP key: AUX as 2nd CD key: AUX as 2nd SAT key: AUX back to AUX: SETUP - 9 - 9 - 2 - TV- AUX SETUP - 9 - 9 - 2 - VCR - AUX SETUP - 9 - 9 - 2 - CBL - AUX SETUP - 9 - 9 - 2 - TNR - AUX SETUP - 9 - 9 - 2 - AMP - AUX SETUP - 9 - 9 - 2 - CD - AUX SETUP - 9 - 9 - 2 - SAT - AUX SETUP - 9 - 9 - 2 - AUX - AUX TROUBLESHOOTING PROBLEM: LED does not blink when you press a key. SOLUTION: Replace the batteries with two (2) new AA alkaline batteries. PROBLEM: LED blinks when you press a key, but home entertainment component does not respond. INSTALLING BATTERIES 1. [. . . ] On the back of the Catalyst 48, push the tab and lift off the battery cover. Match the + and ­ marks on the batteries to the + and ­ marks in the battery case, then insert the new batteries. Test the unit by pressing PWR and any mode key (e. g. , AUX, CBL, VCR, etc. ). If the batteries are inserted correctly, the LED will blink once. NOTE: When batteries need replacement, the Catalyst 48 will blink twice with every key press. Simply replace them and the remote control will be restored to its full functionality, including favorite settings. 5. Repeat steps 1 through 4 for each component you want the Catalyst 48 to control. PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. We recommend highlighting or writing down the code for the brand you wish to program before moving onto step 2. Use the Setup Codes For TV/VCR Combos (on the back side) to locate the brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. SOLUTION: Make sure the Catalyst 48 is aimed at your home entertainment component and is not farther than 15 feet away. Turn on a component (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). We recommend highlighting or writing down the codes and device you wish to program before moving onto step 2. On the Catalyst 48, press a component key once (i. e. , AUX, CBL, VCR, TV, SAT, CD, AMP, or TNR). Use the Manufacturer's Codes (on the back side) to locate the the type of component and brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. 4. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your Code). NOTE: If the device does not have a PWR key, press PLAY. To change Volume Lock to the another mode: 1. On the Catalyst 48, press and hold SETUP until the LED blinks twice, then release SETUP. Now, whenever you press VOL +, VOL ­, or MUTE, volume will be controlled by your mode choice. SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. [. . . ] Now, whenever you press VOL +, VOL ­, or MUTE, volume will be controlled by your mode choice. SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. If you've located a setup code that works, but it has a separate TV code, you'll also need to program it into the Catalyst 48 to access volume control as follows: a. If there is no separate TV code listed, you will need to perform the following steps to access volume control: a. The LED will blink twice. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the Catalyst 48 after entering the channel number. [. . . ]