User manual FUJITSU S7110

[. . . ] S7110. book Page 1 Monday, March 20, 2006 1:56 PM Fujitsu LifeBook S7100 Notebook ® User's Guide S7110. book Page 2 Monday, March 20, 2006 1:56 PM S7110. book Page 3 Monday, March 20, 2006 1:56 PM Copyright Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. The following are registered trademarks of IBM Corporation: IBM, IBM PC AT, IBM PS/2. The ExpressCard word mark and logo are owned by the Personal Computer Memory Card International Association (PCMCIA) and any use of such marks by Fujitsu Computer Systems Corporation is under license. [. . . ] Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password. Your system display won't turn on when the system is turned on or when the system has resumed. Video Problems The built-in display is blank when you turn on your LifeBook notebook. The system may be passwordprotected. Something is pushing on the Closed Cover switch. The notebook is set for an external device only. Clear the Closed Cover switch. (See figure 2-4 on page 6 for location) Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor. Move the display and the brightness control until you have adequate visibility. The angle of the display and the brightness settings are not adequate for your lighting conditions. 63 S7110. book Page 64 Monday, March 20, 2006 1:56 PM LifeBook S7100 Notebook Problem Possible Cause Possible Solutions The built-in display is blank when you turn on your LifeBook notebook. (continued) The LifeBook notebook turned on with a series of beeps and your built-in display is blank. The display goes blank by itself after you have been using it. The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again. Power On Self Test (POST) has detected a failure which does not allow the display to operate. The notebook has gone into Video timeout, Standby mode, Standby mode or Save-to-Disk mode because you have not used it for a period of time. Press any button the keyboard, or move the mouse to restore operation. (The display may be shut off by Standby mode, Auto Suspend or Video Timeout) Contact your support representative. Press any button on the keyboard, or move the mouse to restore operation. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on page 29 for more information) Press any button on the keyboard, or move the mouse to restore operation. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout) Check the Closed Cover switch. (See figure 2-4 on page 6 for location) Check the status indicator panel to verify that the Security icon is blinking. Remove all foreign objects from the keyboard. The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again. Your system display won't turn on when the system is turned on or when the system has resumed. The system may be passwordprotected. A foreign object, such as a paper clip, is stuck between the display and the keyboard. If the spots are very tiny and few in number, this is normal for a large LCD display. If the spots are numerous or large enough to interfere with your operation needs. The display has bright or dark spots. This is normal; do nothing. Display is faulty; contact your support representative. The application display uses only a portion of your screen and is surrounded by a dark frame. You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled. Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. [. . . ] If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows. With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on. [. . . ]