User manual FUJITSU S7010D

[. . . ] S Series. book Page 1 Thursday, February 19, 2004 4:52 PM Copyright Copyright Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. The following are registered trademarks of IBM Corporation: IBM, IBM PC AT, IBM PS/2. The following are registered trademarks of Microsoft Corporation: MS, MS-DOS, Windows. [. . . ] The LifeBook notebook turned on with a series of beeps and your built-in display is blank. Power On Self Test (POST) has detected a failure which does not allow the display to operate. The notebook has gone into Video timeout, Standby mode, Suspend mode or Save-to-Disk mode because you have not used it for a period of time. Press any button the keyboard, or move the mouse to restore operation. (The display may be shut off by Standy mode, Auto Suspend or Video Timeout) Contact your support representative. Press any button on the keyboard, or move the mouse to restore operation. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on page 29 for more information) Press any button on the keyboard, or move the mouse to restore operation. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout) Check the Closed Cover switch. (See figure 2-3 on page 6 for location) Check the status indicator panel to verify that the Security icon is blinking. Remove all foreign objects from the keyboard. The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again. Your system display won't turn on when the system is turned on or when the system has resumed. The system may be passwordprotected. A foreign object, such as a paper clip, is stuck between the display and the keyboard. 62 S Series. book Page 63 Thursday, February 19, 2004 4:52 PM Troubleshooting Problem Possible Cause Possible Solutions The Built-in Display has bright or dark spots. If the spots are very tiny and few in number, this is normal for a large LCD display. If the spots are numerous or large enough to interfere with your operation needs. This is normal; do nothing. Display is faulty; contact your support representative. The application display uses only a portion of your screen and is surrounded by a dark frame. You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled. Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing your display compression setting, (See the Video Features submenu, located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 29 for more information) Press [Fn] + [F7] to increase brightness or doubleclick on the battery gauge and adjust Power Control under battery settings. Try toggling the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on page 29 for more information) Reinstall your device. (See External Monitor Port on page 52 for more information) Check your device and operating system documentation and activate the proper driver. The Display is dark when on battery power. You have connected an external monitor and it does not display any information. The Power Management utility default is set on low brightness to conserve power. Your BIOS setup is not set to enable your external monitor. Your external monitor is not properly installed. Your operating system software is not setup with the correct software driver for that device. Miscellaneous Problems An error message is displayed on the screen during the operation of an application. [. . . ] Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other. TCP/IP (Transmission Control Protocol/Internet Protocol) A standard protocol of the Internet. Wi-Fi Indicates that the interconnectivity test of the organization which guarantees the compatible connection of wireless LAN (Wi-Fi Alliance) has been passed. 111 S Series. book Page 112 Thursday, February 19, 2004 4:52 PM LifeBook S7000 Notebook IP address information IP addressing is much more complicated than can be briefly explained in this document. [. . . ]