User manual FUJITSU P1110

[. . . ] B5FH-5961-01EN-00. book Page 1 Monday, April 29, 2002 2:58 PM Copyright Copyright Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. The following are registered trademarks of IBM Corporation: IBM, IBM PC AT, IBM PS/2. [. . . ] *System CMOS checksum bad ­ run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. *System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. Contact your support representative for repairs. 48 nnnn System RAM Passed Where nnnn is the amount of system memory in kilobytes successfully tested. UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager. Video BIOS shadowed Video BIOS successfully copied to shadow RAM. MODEM RESULT CODES The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are: I I I I I I I I I OK NO CARRIER NO DIALTONE CONNECT 53000 (Connection complete at 53, 000 bps. ) ERROR FAX RING (This means an incoming call. ) BUSY NO ANSWER When using the internal modem with applications that are not factory installed refer to the application documentation. B5FH-5961-01EN-00. book Page 49 Monday, April 29, 2002 2:58 PM Tro ublesho oting Restoring Your Pre-installed Software Your system has been loaded with a valuable utility that allows you to restore your LifeBook notebook disk drive contents as they were originally shipped from the factory. Most often this is necessary if files or software programs (only those files/programs that came preinstalled) become corrupt or accidentally erased. partition, and it must be directly before the backup partition on your hard disk. At the Drive Image Special Edition main screen, click Options> Create New Backup. There is also a button on the main DISE screen that performs the same function. If you created a backup image previously, the new image overwrites the old one. Enlarging the Backup Partition If there is not enough unused space in the backup partition on your hard disk, DISE will resize the partition. DISE will display the minimum, maximum, and recommended sizes for the backup partition. DISE takes the space from the FAT, FAT32, or NTFS partition that you are backing up. If there is not enough unused space in that partition to take, you will not be able to resize the backup partition and create an image file. You can delete files from the FAT, FAT32, or NTFS partition to create more unused space on the hard disk. Restoring a Backup Image You can restore either a factory image or a backup image you created. Be aware that restoring a backup image will replace the contents of the C:\ partition with the image you restore. From the DISE main window, click Options > Restore Backup to restore an image you created, or click Options > Restore Factory Backup to restore the factory image. Drivers and Applications Restore CD The Drivers and Application CD can be used to selectively re-install drivers and/or applications that may have been un-installed or corrupted. [. . . ] Perform the following steps. I I Click [PRISM 11Mbps Wireless LAN for Windows]. Click [Change/Remove]. A window appears asking you if you really want to remove the driver. When the driver is removed, a window appears showing that the driver has been removed. Shut down Windows, and turn off the computer. 89 B5FH-5961-01EN-00. book Page 90 Monday, April 29, 2002 2:58 PM LifeBook P1000 Notebook ­ Appendix Problem I want to remove the driver (Windows XP) Possible Cause Possible Solution Windows XP: When removing the driver, make sure that the device is attached to the computer. [. . . ]