User manual FUJITSU MOBILE H Operating Manual

[. . . ] Introduction Index Important notes CELSIUS Mobile H Preparing the workstation for use Working with the workstation Operating Manual Security functions Connecting external devices Settings in BIOS Setup Troubleshooting and tips Memory expansion Technical data May 2002 edition DPMS and VESA are registered trademarks of Video Electronics Standards Association. Intel is a registered trademark, Pentium and Celeron are trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation. OS/2 and PS/2 are registered trademarks of International Business Machines, Inc. [. . . ] When not using the workstation for long periods of time, first end the energy saving mode, then switch off the workstation. Never switch off the workstation with the Suspend/Resume button while the workstation is in one of the energy-saving modes. If your workstation is in an energy-saving mode: · · · · · · · Do not connect any external devices. Do not attempt to switch the workstation on if the built-in battery is flat. Do not replace or remove the battery. Energy-saving modes of workstation You can set two energy-saving modes with your workstation. In the Suspend mode (Suspend to DRAM/Standby) all current data (active programmes, files) are buffered in the main memory, and in the Save-to-Disk mode (Save to Disk/HibernateMode) all current data are saved on the hard disk. After the workstation is switched on, you can continue working exactly where you left off before. Operating systems with ACPI (Windows 2000 and Windows XP) i For operating systems with ACPI you can set the energy-saving functions under Settings Control Panel - Power Management (e. g. You can configure the Suspend/Resume button and the lid switch in the Settings tab under Settings ­ Control Panel ­ Power Management. Settings for energy-saving functions in the BIOS Setup are not taken into account by operating systems with ACPI. 36 A26391-K124-Z100-1-7619 Working with the workstation Changing settings Ê Ê Ê Ê Ê Double-click on the My Computer symbol. Double-click on the Power management symbol in the Control Panel window. Click on OK to save the settings. The Properties dialogue field appears. i Under Windows 2000 the Hibernate mode is switched off in the default setting. Hard disk The hard disk is the most important storage medium of your workstation. You can work considerably faster and more efficiently if you copy applications and files from floppy disks or CDs to your hard disk. When the hard disk is accessed, the hard disk indicator lights up. Inserting and removing modules Modules can be optical drives, additional hard disk or floppy disk drives or batteries. ! Ê Ê Ê Only use modules released for this workstation. Open the LCD display panel. A26391-K124-Z100-1-7619 37 Working with the workstation Removing modules 1 2 Ê Push the slide in the direction of the arrow (1) up to the stop and hold it in place. i Ê To remove the left-hand module, push the slide to the right. To remove the right-hand module, push the slide to the left. Remove the module the direction of the arrow (2). 38 A26391-K124-Z100-1-7619 Working with the workstation Installing modules 1 2 Ê Push the slide in the direction of the arrow (1) up to the stop and hold it in place. i Ê Ê To install the left-hand module, push the slide to the right. To install the right-hand module, push the slide to the left. Position the module at the edge of the casing (2) and then press it into the workstation. Release the slide (2). A26391-K124-Z100-1-7619 39 Working with the workstation Optical drives Your workstation is fitted with a combo drive (CD-RW/DVD). ! This device contains a light-emitting diode, classified according to IEC 825-1:1993: LASER CLASS 1, and must not be opened. Thus you avoid dust contamination, scratches, bending or other damage. Protect your CDs/DVDs from dust, mechanical vibration and direct sunlight!Avoid storing a CD/DVD in areas subject to high temperatures or humidity. You may use both 8-cm and 12-cm CDs/DVDs in the optical drive. When using CDs/DVDs of poor quality vibrations and reading errors may occur. Optical drive indicator The indicator flashes when a CD/DVD is inserted. The indicator lights up when the drive is accessed. i If the indicator does not go out after the CD/DVD is inserted, and continues to flash, the CD/DVD is probably damaged or dirty. Inserting or removing a CD/DVD The workstation must be switched on. Ê Ê Ê or Push the insert/eject button. [. . . ] The serial number is located on a sticker on the underside of the workstation. Notes of any messages that appear on the screen and information on acoustic signals. Any changes you have made to the hardware and/or software or the BIOS settings after receiving the workstation. Your system configuration and all peripheral devices connected to your system. [. . . ]