User manual FUJITSU L470

[. . . ] No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu PC Corporation. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu PC Corporation. Fujitsu PC Corporation disclaims liability for any inaccuracies, errors, omissions, or future changes. Fujitsu and the Fujitsu logo are registered trademarks, and LifeBook is a trademark of Fujitsu Limited. [. . . ] (See page 61. ) Table 4-9 shows the names of the menu fields for the PCI Configuration submenu, all the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help PCI Configuration v IRQ Reservation Reserve specific IRQs for use by legacy ISA devices. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-9 PCI Configuration Submenu 88 LifeBook L Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k L S e r i e s Table 4-9 Fields, options and Defaults for the PCI Configuration Submenu Menu Field IRQ Reservation: Options Selects the IRQ Reservation Submenu. Default -- Description This menu allows you to set aside interrupt levels for legacy ISA devices. 89 Four Section Four IRQ Reservation Submenu of the PCI Configuration Submenu The IRQ Reservation Submenu is for reserving interrupts for legacy ISA devices. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 61. ) Table 4-10 shows the names of the menu fields for the IRQ Reservation submenu, all the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help IRQ Reservation IRQ IRQ IRQ IRQ IRQ IRQ IRQ 3: 4: 5: 7: 9: 10: 11: [Available] [Available] [Available] [Available] [Available] [Available] [Available] Reserve the specified IRQ for use by legacy ISA devices. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-10 IRQ Reservation Submenu 90 LifeBook L Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k L S e r i e s Table 4-10 Fields, options and Defaults for the IRQ Reservation Submenu Menu Field IRQ 3: IRQ 4: IRQ 5: IRQ 7: IRQ 9: IRQ 10: IRQ 11: CAUTION Only IRQs 3, 9, 10 & 11 can be reserved without conflict. Default [Available] [Available] [Available] [Available] [Available] [Available] [Available] Description Turns on or off the reservation for that IRQ for legacy ISA devices. Turns on or off the reservation for that IRQ for legacy ISA devices. Four 91 Section Four DMI Event Logging Submenu of the Advanced Menu The DMI Event Logging Submenu is for setting up the logs DMI event logging. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 61. ) Table 4-11 shows the names of the menu fields for the DMI Event Logging submenu, all the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help DMI Event Logging Event log capacity: Event log validity: Space Available Valid Clear all DMI event logs: [No] Event Logging: System Boot Event: [Enabled] [Disabled] 'Yes' clears all DMI event logs at next boot. The value is reset to 'No' after clearing logs. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-11 DMI Event Logging Submenu 92 LifeBook L Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k L S e r i e s Table 4-11 Fields, options and Defaults for the DMI Event Logging Submenu Menu Field Event log capacity: Event log validity: Clear all DMI event logs: Options Display only. Default [Space Available] [Valid] [No] A Yes selection causes the event logs to clear at the next boot. Once the logs are cleared this automatically sets to No until reset to yes by selecting yes here. Description Event Logging: System Boot Event: Enabled; Disabled. Enabled; Disabled. [Enabled] [Disabled] 93 Four Section Four SECURITY MENU ­ SETTING THE SECURITY FEATURES The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 61. ) Table 4-12 shows the names of the menu fields for the Security menu, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. The default condition is no passwords required and no write protection. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Info Exit Item Specific Help Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Clear Clear [Enter] [Enter] Supervisor Password controls access to the setup utility. Diskette access: [All] Password on boot: [Disabled] Power Management security: [Disabled] Fixed disk boot sector: Fixed disk security: Primary Master: Secondary Master: [Normal] [Disabled] [Disabled] F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-12 Security Menu 94 LifeBook L Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k L S e r i e s Table 4-12 Fields, Options and Defaults for the Security Menu Menu Field Supervisor Password is: User Password is: Set Supervisor Password: Options -- -- [Enter] Default Clear Clear -- Description A display-only field. Set is displayed when the system supervisor password is set and Clear when it is not. Set is displayed when the general user password is set, and Clear when it is not. The Supervisor Password may be up to seven characters long and must include only letters or numbers. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor Password is set it must be used to access the BIOS setup utility. Note: This field can only be accessed if the Supervisor Password is set. [. . . ] An American National Standards Institute (ANSI) standard for connecting multiple (up to 7) high speed parallel devices to a computer. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data. Shadow RAM A technique of copying data or applications stored in ROM (Read Only Memory) into RAM (Random Access Memory) for access during actual operation. RAM is much faster to access than ROM, however ROM contents are not lost when power is removed. Shadowing allows permanently stored information to be rapidly accessed. [. . . ]