User manual FUJITSU E350

[. . . ] COPYRIGHT Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. Fujitsu and the Fujitsu logo are registered trademarks and LifeBook is a trademark of Fujitsu Limited. Built for Humans and ErgoTrac are trademarks of Fujitsu PC Corporation. [. . . ] If any two ports or devices, serial or parallel, have the same I/O address assigned your notebook will not function normally. Please keep a record of original settings before making any changes in the event that a restoration is required. See your hardware and software documentation as well as the setup utility to determine settings, limitations, etc. I/O Device Configuration Submenu of the Advanced Menu The I/O Device Configuration submenu provides the ability to set the I/O addresses and interrupt levels for the parallel and serial ports, and disk drive controllers of your notebook. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 71. ) 84 PhoenixBIOS Setup Utility Advanced I/O Device Configuration Serial port A: Base I/O address: Interrupt: Serial port B: Mode: Base I/O address: Interrupt: Base I/O address: DMA channel: Parallel port: Mode: Base I/O address: Interrupt: Floppy disk controller: Local Bus IDE adapter: [Enabled] [3F8] [IRQ 4] [Enabled] [FIR] [2E8] [IRQ 3] [118] [DMA 3] [Enabled] [Bi-directional] [378] [IRQ 7] [Enabled] [Both] Item Specific Help Configure serial port A using options: [Disabled] No configuration [Enabled] User configuration [Auto] BIOS or OS chooses F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu v F9 Setup Defaults F10 Save and Exit Figure 4-5 I/O Device Configuration Submenu LifeBook E Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k E S e r i e s Table 4-5 shows the names of the menu fields for the I/O Device Configuration submenu, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. POINT To prevent IRQ and address conflicts, avoid changing the default settings. If you must change the settings, you can call 1-800-8FUJITSU for technical assistance. POINT All I/O addresses in Table 4-5 are in hexadecimal. The BIOS will warn you of a resource conflict by placing a yellow asterisk next to each device that is in conflict. 85 Four CAUTION Section Four Table 4-5 Fields, Options and Defaults for the I/O Device Configuration Submenu of the Advanced Menu Menu Field Serial Port A: Options Disabled; Enabled; Auto. Default [Enabled] Description Configures the serial port A using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). Allows user to set the serial port base I/O address when port A is Enabled. Configures the serial port B using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). Allows user to set the serial port base I/O address when port B is Enabled. Base I/O address: Interrupt: Serial Port B: 3F8; 2F8; 3E8; 2E8. Disabled; Enabled; Auto. [3F8] [IRQ 4] [Enabled] Mode: Base I/O address: IrDA; FIR. 3F8; 2F8; 3E8; 2E8. [FIR] [2E8] 86 LifeBook E Series from Fujitsu C o n f i g u r i n g Yo u r L i f e B o o k E S e r i e s Table 4-5 Fields, Options and Defaults for the I/O Device Configuration Submenu of the Advanced Menu Menu Field Interrupt: Base I/O address: Options IRQ 3; IRQ 4; IRQ 10; IRQ 11. Default [IRQ 3] [118] Description Allows user to set the serial port interrupt when port B is Enabled. When the mode for serial port B is set to FIR, this option is available allowing the user to set the base I/O address for the FIR of serial port B. When the mode for serial port B is set to FIR, this option is available allowing the user to set the DMA channel for the FIR of serial port B. Configures the parallel port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). When the parallel port is enabled this option is available allowing the user to set the mode for the parallel port. Bi-directional allows two-way transfer of information between your notebook and a connected parallel device. Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP Mode allows communication with the ECP class of parallel I/O devices. Four 87 DMA channel: DMA 1; DMA 3. [DMA 3] Parallel port: Disabled; Enabled; Auto. [Enabled] Mode: Output Only; Bi-directional; ECP. [Bi-directional] Section Four Table 4-5 Fields, Options and Defaults for the I/O Device Configuration Submenu of the Advanced Menu Menu Field Options Default Description Base I/O address: Interrupt: Floppy disk controller: 378; 278; 3BC. [378] [IRQ 7] [Enabled] Allows user to set the parallel port base I/O address when the parallel port is Enabled. [. . . ] 11, 40, 42, 49­52, 59, 70, 74, 79­80, 107, 109­111, 120, 122­125, 127­128, 141­143, 151, 156, 170, 172 Memory Cache . 3­5, 8, 22­23, 27, 38, 47­48, 52, 55­56, 58­59, 96, 111, 128, 135, 138, 149, 151, 157, 164, 173 Monitor . 5, 10, 37, 55, 69, 127­128, 139, 145, 148, 166, 169, 171 Mono microphone. 5, 10, 32­37, 82, 89­90, 102, 114, 127­128, 139, 145­148, 151, 155­156 Mouse cursor . [. . . ]