User manual FUJITSU 990TX2

[. . . ] COPYRIGHT Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. Fujitsu and the Fujitsu logo are registered trademarks and LifeBook is a trademark of Fujitsu Limited. Built for Humans and ErgoTrac are trademarks of Fujitsu Personal Computer Corporation. [. . . ] Always leave the default setting for Enable ACPI [Yes]. 87 Section Three Chipset Configuration Submenu of the Advanced Menu The Chipset Configuration Submenu is for configuring the features of the AGP video device. Follow the instructions for navigating through the Setup Utility to make any changes. (See page 59. ) Table 3-13 shows the names of the menu fields for the Chipset Configuration submenu, all the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Figure 3-13 Chipset Configuration Submenu 88 LifeB ook 90 0 Series from Fuj itsu C onfi gu ri n g Your Li fe Book 900 S er ie s Table 3-13 Chipset Configuration Submenu Menu Field AGP Data Tranfer Type: AGP Aperture Size: Options Default Description Sets the Data Transfer type for the AGP video device. Sets the maximum size of the Graphics Aperture for the AGP video device. Standard (lx); High Speed (2x) [Standard (lx)] 64MB; 128MB; 256Mb; 4MB; 4­256 MB [64MB] Exiting from the Advanced Menu When you have finished setting the parame ters on the Advanced Menu, you can either exit from setup utility or move to another menu. If you wish to exit from setup utility, press the Esc key to go to the Exit menu. If you wish to move to another menu, use the cursor keys. 89 Section Three SECURITY MENU ­ SETTING THE SECURITY FEATURES The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See page 59. ) Table 3-14 shows the names of the menu fields for the Security menu, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. The default condition is no passwords required and no write protection. Figure 3-14 Security Menu 90 LifeB ook 90 0 Series from Fuj itsu C onfi gu ri n g Your Li fe Book 900 S er ie s POINT If you set a password, write it down and keep it in a safe place. If you forget the password you will have to contact your support representative to regain access to your secured functions and data. POINT If you make an error when re-entering the password a [Warning] will be displayed on the screen. Press the Esc key to abort the password setting process. CAUTION Entering a password incorrectly 3 times in a row will cause the keyboard and mouse to be locked out and the warning [System Disabled]to be displayed. If this happens restart the computer by turning off and on the power with the power switch and use the correct password on reboot. CAUTION If the Power Management Security is Enabled and the Password on Boot is Disabled you will not be able to resume operation from the Suspend or Save-toDisk modes. 91 Section Three Table 3-14 Fields, Options and Defaults for the Security Menu Menu Field Supervisor Password is: User Password is: Set Supervisor Password: Options -- -- [Enter] Default Clear Clear -- Description A display-only field. Set is displayed when the system supervisor password is set and Clear when it is not. Set is displayed when the general user password is set, and Clear when it is not. The Supervisor Password may be up to seven characters long and must include only lower-case letters or numbers. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a Supervisor Password is set it must be used to access the BIOS setup utility. (This field can only be a ccessed if the Supervisor Password is set. ) Sets, changes or cancels the User Password. The User Password may be up to seven characters long and must include only lower case letters or numbers. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a User Password is set it must be used to access the BIOS setup utility. Set User Password: [Enter] -- 92 LifeB ook 90 0 Series from Fuj itsu C onfi gu ri n g Your Li fe Book 900 S er ie s Table 3-14 Fields, Options and Defaults for the Security Menu Menu Field Diskette access: Options All; Supervisor Only. [. . . ] 32-33, 57, 133, 163, 165, 178 194 LifeB ook 90 0 Series from Fuj itsu Index Function keys . 4-6, 8, 17-19, 23-24, 29, 32-33, 40, 46, 49, 69, 76-77, 91, 115-116, 131, 140-141, 144, 147, 151-152, 158, 164, 167, 178, 180, 187-188 Kilobyte . 2-3, 6-7, 11, 20, 24, 26-28, 41, 50, 115-117, 123-124, 128, 179-180, 185 Low battery alarm . 2-3, 7-8, 48, 115-116, 129-130, 140, 177-178, 180, 185-186 MMX technology . [. . . ]