User manual FUJITSU SIEMENS T-BIRD

[. . . ] BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1495-Z120-1-6319 Printed in the Federal Republic of Germany AG 0902 09/02 A26361-D1495-Z120-1-6319 German English Mainboard D1495 Technisches Handbuch Technical manual Ausgabe September 2002 September 2002 edition Pentium and Celeron are registered trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. [. . . ] System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service centre). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the mainboard. Normal operation (default setting). Reserved - switch 3 and switch 4 Switch 3 and 4 are reserved. The position of the switch doesn't matter. A26361-D1495-Z120-1-6319 English - 11 Replacing processor Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter!memory modules, AGP and PCI extension boards) are still supplied with power. Replacing processor Technical data SiS 645DX with 400/533 MHz Front Side Bus in the mPGA478 design. A current list of the processors supported by this mainboard is available on the Internet at: www. fujitsu-siemens. de/mainboards. Removing and installing processors Ê Remove the fan that there may be and the heat sink. 3 2 4 5 1 A Ê Ê Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). i Ê The angled corner of the processor can also be at a different location than shown in the illustration. Push the lever back down until it clicks into place (5). 12 - English A26361-D1495-Z120-1-6319 Replacing processor Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it. Please note that, depending on the heat sink used, different heat sink mounts are required on the mainboard. i If a counter-plate is mounted on the underside of the mainboard for reinforcement, no heat sinks of the type "Intel Boxed" may be used. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. Replacing the lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion!The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. They must be disposed of in accordance with local regulations concerning special waste. The plus pole must be on the top! 16 - English A26361-D1495-Z120-1-6319 Adding PCI cards The lithium battery holder exists in different designs that function in the same way. 2 3 3 2 1 3 Ê Ê Ê Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the holder (1). Insert a new lithium battery of the same type into the socket (3). A26361-D1495-Z120-1-6319 English - 17 BIOS update BIOS update When should a BIOS update be carried out?Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software. The BIOS updates are available on the Internet at www. fujitsu-siemens. de/mainboards. BIOS update under DOS with bootable BIOS update floppy disk - brief description Ê Ê Ê Ê Ê Ê Download the update file from out website to your PC. [. . . ] Service Processor not properly installed The server management controller has not been correctly installed. If the message is still displayed, please contact your sales outlet or customer service centre. Storage Extension Group = xy Configuration error, x Storage Extensions(s) found, configured are y SE(s). The specified number of storage expansion units (SEs) in the BIOS Setup menu Server - Storage Extensions - Number of connected SE is incorrect. [. . . ]