User manual FUJITSU SIEMENS SCENIC 850

[. . . ] 10 Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 BIOS options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] in the complete Technical Manual for the system board and in the description "BIOS Setup". Further information to drivers is provided on the supplied drivers diskettes or on the "Drivers & Utilities" or "ServerStart" CD. For detailed information please look at chapter "Installing drivers". The latest BIOS version or drivers can be found on the internet under http://www. siemens. de/computer/service . Notational conventions The meanings of the symbols and fonts used in this manual are as follows: ! i Ê Ë Ú Pay particular attention to texts marked with this symbol. Failure to observe this warning endangers your life, destroys the system, or may lead to loss of data. Supplementary information, remarks and tips follow this symbol. Texts which follow this symbol describe activities that must be performed in the order shown. This symbol means that you must press the Enter key. Texts in this typeface are screen outputs. Texts in this bold typeface are the entries you make via the keyboard. "Quotation marks" indicate names of chapters and terms that are being emphasized. A26361-D1107-Z180-10-7619 1 Features Features Function Processor socket Processor Formfactor Front Side Bus in MHz Chipset Memory sockets ISA slots PCI slots ISA/PCI shared AGP-Port System monitoring Thermal Management Wake On LAN Keyboard On IrDA Chipcard reader Save to Disk (ACPI S4) Save to RAM(ACPI S3) LAN onboard Audio onboard VGA onboard 4MB Display Cache x x x x ---x x x ----- D1107-A Slot 1 D1107-B Slot 1 Intel Celeron or Pentium II Intel Celeron or Pentium II or Pentium III or Pentium III ATX ATX 66/100 440BX 3 DIMM 1 4 1 1 x x x x 66/100 440BX 3 DIMM 1 4 1 1 x x x x ! Computer system boards and components contain very delicate IC chips. To protect them against damage caused from electric static, you have to follow some precautions: · · · Unplug your computer when you work inside. Use a grounded wrist strap. Place the system board and the components on a grounded antistatic pad whenever you work outside the computer. Once you have installed the system board, you should remove the battery protection (i. e. the thin plastic plate between battery and contact spring). 2 A26361-D1107-Z180-10-7619 Mechanics Mechanics Layout ATX 12"' x 8'' (304, 8 mm x 203, 2 mm) Some of the following connectors are optional and may therefore not be included on your system board. 1 23 AGP ISA2 PCI 3 PCI 2 Slot 1 2 5 1 1 = Serial port 1 2 = PS/2 mouse port 3 = PS/2 keyboard port 3 4 6 7 4= 5= 6= 7= Parallel port USB connection 2 USB connection 1 LAN port The components and connectors marked do not have to be present on the system board. PCI 1 PCI5 PCI4 ISA1 A26361-D1107-Z180-10-7619 3 Mechanics 1 23 4 5 67 8 9 10 11 15 14 1 23 13 AGP ISA2 ISA1 PCI 3 PCI 2 Slot 1 12 1= 2= 3= 4= 5= 6= 7= 8= I2C connector (for temperature sensor) Internal chipcard reader or serial port 2 Power supply Floppy disk drive IDE drives 3 and 4 (secondary) Wake On LAN ON/OFF switch Fan 2 9 = IDE drives 1 and 2 (primary) 10 = Front panel connector 11 = IrDA 12 = USB chipcard reader 13 = Fan 1 (e. for the processor) 14 = Power supply monitoring 15 = Intrusion connector * The components and connectors marked do not have to be present on the system board. *: For correct installation please refer to chapter "Temperature monitoring / system monitoring" in the Technical Manual. 4 A26361-D1107-Z180-10-7619 PCI 1 PCI5 PCI4 Mechanics Connectors and Jumpers ! 2 Some of the following connectors are optional! I C connector (for ambient/external temperature sensor) for optional temperature sensor (LM75) Pin Signal 1 1 3. 3 V standby 2 Clock 3 Data 4 GND Refer to chapter "Temperature monitoring / system monitoring" in the Technical Manual. Internal chipcard reader or serial port 2 (COM2) (external via wire) 2 1 Pin 1 3 5 7 9 11 13 15 Signal DCD 2 (low asserted) SIN 2 (high asserted) SOUT 2 (high asserted) DTR 2 (low asserted) GND EXT SMI (low asserted) RESETDRV (high asserted) GND Pin 2 4 6 8 10 12 14 16 Signal DSR 2 (low asserted) RTS 2 (low asserted) CTS 2 (low asserted) PC_ON_Strobe VCC Auxiliary VCC GND Key A26361-D1107-Z180-10-7619 5 Mechanics Power supply ATX connector 20 11 10 Pin 1 3 5 7 9 11 13 15 17 19 Signal +3. 3 V GND GND GND +5 V Auxiliary +3. 3 V GND GND GND +5 V Pin 2 4 6 8 10 12 14 16 18 20 Signal +3. 3 V +5 V +5 V Powergood (high asserted) +12 V -12 V PS on (low asserted) GND -5 V +5 V 1 Wake on LAN (WOL) connector 1 Pin 1 2 3 Signal +5 V Auxiliary GND Wake pulse (high asserted) Power on switch connector (ON/OFF switch) 1 Pin 1 2 Signal GND Power on pulse (low asserted) Fan 2 connector for system fan or CPU fan (if external temperature sensor is in use) Pin Signal 1 1 GND 2 +12 V 3 Fan sense Refer to chapter "Temperature monitoring / system monitoring" in the Technical Manual. 6 A26361-D1107-Z180-10-7619 Mechanics Front panel connector (version 1) 2) Message LED 2) 1) 2) Power On LED Reset adapter HD-LED 1 2 SCSI LED Input 2) 3) Speaker 2) 1) Reset adapter from 4pin female to 2pin male. 3) The same interface. Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal Reserved Anode Standby LED Key Anode PON_LED Not connected Cathode PON_LED (GND) Anode Message LED Cathode Message LED Key Anode HD_LED Cathode HD_LED GND (for Reset and Power button) Power Button Not connected Reset Button Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Signal Speaker Key GND VCC Key pin Key Key Key pin Key Key Key Not connected SCSI LED Input SCSI LED Input Not connected A26361-D1107-Z180-10-7619 7 Mechanics Front panel connector (version 2) 1) Reset 1) Message LED 1) 1) HD-LED Power On LED 1 2 Power On/Off SCSI LED Input 1) 2) Speaker 2) 1) Cable is not included in the delivery scope. Example T0 T1 T2 Fan 0 destination supervision control Fan 1 destination supervision control Fan 2 destination supervision control processor temperature system temperature external temperature via optional LM75 sensor Extended ATX power supply 1 Standard 2 Workstation Sensor in CPU integrated Sensor onboard -3 Server -- yes power supply fan yes yes (0 V, 6-12 V) ------------system fan yes yes (0 V, 6-12 V) processor fan yes no (12 V) Hardware requirements Power supply: Power supply fan must be controllable by system board (22KHz PWM signal with 3. 3V) and needs a sense-pin for rpm-measurement. Fan sense: Ripple pulse width: Number of revolutions e. g. : 2 ripples per rotation T low and T high > 0. 6 ms at 100% PWM: maximum 14000 Rpm at 50% PWM: minimum 800 Rpm Siemens S26113-E425 or. E427 A26361-D1107-Z180-10-7619 11 Mechanics Fan: The fan speed must be controllable from 6 - 12 V (start voltage: 12 V). Therefore the fan must have a mechanical suitability as well as a 3-pole-plug with a sense-pin for rpm-measurement. Fan sense: Ripple pulse width: Current: number of revolutions e. g. : 2 ripples per rotation T low and T high > 0. 6 ms blocking fan at 12 V: 1. 6 A rotating fan at 6V / 12V: 0. 3A / 0. 6 A at 12V: maximum 14000 Rpm at 6V: minimum 800 Rpm Papst type 412 F/2H as processor fan Sensor for internal temperature: Housing temperature is read by an onboard sensor. CPU temperature is read by an onboard sensor but only with processors which have an integrated temperature diode. Sensor for external temperature: Use only a Siemens Sensor: e. g. [. . . ] 168 pin, 3. 3V, 100 MHz SDRAM 2M, 4M, 8M, 16M and 32M x 64 bit 2M, 4M, 8M, 16M and 32M x 72 bit (with ECC) For one socket 16, 32, 64, 128 or 256 Mbyte Granularity: * The EEPROM of PC100 modules contains a number of critical timing parameters and data regarding the chip and the module vendor. Due to this the system board will properly recognize the module by reading all important timing parameters specified in the EEPROM via theSerial Presence Detect interface. Troubleshooting Message BIOS update The System BIOS provides optimum support for the processor you have chosen. If the message BIOS update for installed CPU failed appears the microcode required for the processor inserted must still be loaded. Further information on this is available in the "BIOS Setup" manual on the "Drivers & Utilities" CD provided. The screen stays blank If your screen stays blank this may have the following cause: The wrong RAM memory module has been inserted Ê See the chapter "Main Memory" for information which memory modules can be used. ACPI S3 (Save-to-RAM) and/or ACPI S4 (Save-to-Disk) doesn't work This system board is fully compliant for ACPI S3 and S4. [. . . ]