Detailed instructions for use are in the User's Guide.
[. . . ] The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com
Dieses Handbuch wurde auf Recycling-Papier gedruckt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1107-Z120-1-7419 Printed in the Federal Republic of Germany AG 0100 01/00
A26361-D1107-Z120-1-7419
Deutsch
E li h English
Systembaugruppe D1107 System Board D1107
Technisches Handbuch Technical Manual
Ausgabe Januar 2000 January 2000 edition
Intel, Pentium und Celeron sind eingetragene Warenzeichen und MMX und OverDrive sind Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. [. . . ] Direct Rambus, RIMM, SO-RIMM, and Direct RDRAM are trademarks of Rambus Inc. If you pass on the device to third parties, you should also pass on this manual. Be sure to read this page carefully and note the information before you open the device. You cannot access the components of the system board without first opening the device. How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please note the information provided in the chapter "Safety" in the Operating Manual of the device. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the chapter , , Add-on modules" - , , Replacing the lithium battery".
!
A26361-D1107-Z120-14-7419
English - 1
Important notes
The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual of the receiving device. Connecting cables for peripherals must be adequately insulated to avoid interference.
!
i
Components can become very hot during operation. Make sure you do not touch components when making extensions to the system board. The LAN RJ45 connector is equipped with a yellow and a green LED (light emitting diode). 1 = Yellow indicator 2 = Green indicator
1
2
Green Yellow
a connection exists (e. a Magic PacketTM is being received.
8 - English
A26361-D1107-Z120-14-7419
Features
Resource table
Keyboard Serial interface COM1 Serial port COM2 assigned IRQ IRQ1 3 4 3 4 possible IRQ Possible Address (hex) 03F8, 02F8 03E8, 02E8 02E8, 02F8 03E8, 03F8 2 0, 1, 3 Possible DMA
Floppy disk drive controller IRQ6 Parallel interface LPT1 5, 7 0278, 0378, 03BC RTC IRQ8 USB controller PnP Mouse controller IRQ12 Numeric processor IRQ13 IDE controller 1 IRQ14 01F0-01F7 IDE controller 2 IRQ15 0170-0177 LAN PnP "assigned IRQ" = interrupts assigned as shipped "Possible IRQ" = these interrupts can be used for your particular application "Possible address" = this address can be used for your particular application "Possible DMA" = these DMAs can be used for your particular application
PCI bus interrupts
The following table shows which PCI bus interrupts on the system board are assigned. PCI bus interrupt A A A B C D D D Component on system board: PCI bus slot 5 PCI bus slot 1 AGP slot PCI bus slot 2 PCI bus slot 3 PCI bus slot 4 USB controller LAN controller
A26361-D1107-Z120-14-7419
English - 9
Settings with switches
Settings with switches
1
23
AGP
ISA2
PCI 3
PCI 2
Slot 1
ON
12345678
OPEN / OFF
Switch 1 = must be set to off Switch 2 = System BIOS recovery (RCV) Switch 3 = Write protection for floppy disks
Switch 4 = reserved Switches 5 - 8 = clock frequency
10 - English
A26361-D1107-Z120-14-7419
PCI 1
PCI5
PCI4
ISA1
Settings with switches
Recovering System BIOS - switch 2
Switch RCV enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service center).
On Off
The System BIOS executes from standard floppy drive A: and the inserted "FlashBIOS-Diskette" restores the System BIOS on the system board. Normal operation (default setting).
Write protection for floppy disks - switch 3
Switch 3 is used to define whether floppy disks can be written or deleted in the standard floppy disk drive. To write and delete floppy disks, the write-protection in BIOS Setup must be disabled (in menu Security, the field Diskette Write must be set to Enabled).
On Off
The standard floppy disk drive is write-protected. Read, write and delete floppy disks is possible (default setting).
Clock frequency - switches 5 to 8
!
The switches may only be set as specified in the tables below for the particular processor used. There are also processors, which automatically always operate at the proper frequency, regardless of the switch position. As these new processors do not differ externally from the previous processors, we recommend always setting the switches in accordance with the processor. This system board you may use with Pentium II processors with 66 MHz or 100 MHz Front Side Bus or with Pentium III processors with 100 MHz Front Side Bus or with Celeron processors with 66 MHz Front Side Bus. [. . . ] If the processor has a temperature sensor or a fan, attach the associated cable to the connector for the temperature sensor or the fan on the system board.
Removing the processor
Ê Ê
If the processor has a temperature sensor or a fan, pull out the associated cable. Press the clamps (2) on either side of the processor slightly inwards (A) or outwards (B) and pull the processor up and out. Use a screwdriver if necessary.
14 - English
A26361-D1107-Z120-14-7419
Add-on modules
Upgrading main memory
These slots are suitable for 16, 32, 64, 128 and 256 Mbyte SDRAM memory modules of the DIMM format. SDRAM memory modules must be designed for a clock frequency of 100 MHz or higher (meets PC100 specification).
Installing memory modules
!
2
2
Ê Ê
Flip the holders on each side of the relevant location outwards. [. . . ]