User manual FUJITSU SIEMENS SCENIC W300 (I845GE)

[. . . ] BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com/mainboards Vous avez . . . . . . des questions techniques ou des problèmes ?Veuillez contacter : · Votre partenaire Commercial · Votre point de Vente Les dernières informations ainsi que les updates (p. ex. BIOS-Update) par rapport à nos cartes mères sont à votre disposition sur Internet : http://www. fujitsu-siemens. com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1562-Z121-1-6319 Printed in the Federal Republic of Germany AG 1103 11/03 A26361-D1562-Z121-1-6319 Deutsch English Mainboard D1562/D1561 Français Technisches Handbuch Technical Manual Ausgabe November 2003 November 2003 edition Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. [. . . ] This LAN controller supports the transfer rates of 10 Mbit/s, 100 Mbit/s and the LAN controller 82547EI additionally supports 1000 Mbit/s. The LAN controller is equipped with a 2 KB transmission and receiving buffer (FIFO) and supports WOL function through Magic Packetä. The LAN controller 82547EI supports also Basic Alert-on-LAN II and Alert Standard Format (ASF). The LAN RJ45 connector has two LEDs (light emitting diodes). 1 2 LED 1 lights green - a connection exists (e. g. LED is blinking green: activity LED 2 lights differently with the two possible LAN controllers: Link Mode: the LAN connection is active. 82562EZ 10 Mbit/s 100 Mbit/s 1000 Mbit/s off yellow 82547EI off green yellow 10 Mbit/s 100 Mbit/s WOL mode: received. a Magic PacketTM is being 82562EZ off yellow 82547EI off green - A26361-D1562-Z121-1-6319 English - 11 Internal ports and connectors Graphics port - Supported screen resolutions Depending on the operating system used, the screen resolutions in the following table refer to the mainboard screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller. Screen resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200 1920 x 1440 2048 x 1536 Refresh rate (Hz) 120 120 100 100 100 75 60 Colour 32 bit 32 bit 32 bit 32 bit 16 bit 16 bit 16 bit Features 2D+overlay 2D+overlay 2D+overlay 2D 2D 2D 2D Internal ports and connectors The positions of the internal ports and connectors are shown on the Cover. Additional information on some ports is also provided here. Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66 or ultra ATA/100 mode. Connect the cable to the hard disk and to the connector on the mainboard. Ê Ê A serial ATA/150 hard disk must be connected with a serial ATA cable. If no counter-plate is mounted, you can use both "Intel Boxed" heat sinks and standard heat sinks. If you use the "Intel Boxed" heat sink, the mainboard will bend due to the high pressure of the retaining clips. Depending on the configuration variant, you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it. Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard. A26361-D1562-Z121-1-6319 English - 21 Upgrading main memory Upgrading main memory Technical data Technology: Size: DDR 266, DDR 333 or DDR 400 unbuffered DIMM modules 184-Pin; 2. 5 V; 64 Bit, no ECC 128 Mbytes up to 4 Gbyte DDR 266 SDRAM 128 Mbytes up to Gbyte DDR 333 SDRAM 128 Mbytes up to Gbyte DDR 400 SDRAM 128, 256, 512 or 1024 Mbyte for one socket Granularity: A current list of the memory modules recommended for this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2, 5 V memory modules. DDR-DIMM memory modules must meet the PC2100, PC2700 or PC3200 specification. The mainboard has two memory channels (channel A and channel B) with two slots each (slot 1 and 3 or slot 2 and 4). The maximum system performance is available when identical memory modules (same order number, same manufacturer, same size, memory density) are used in a memory slot 1 and 2 or memory slot 3 and 4. slot 4 slot 3 Channel B Channel A slot 2 slot 1 Number of inserted memory modules slot to be used Channel A, slot 1 Channel A, slot 3 Channel B, slot 2 Channel B, slot 4 X 1 X 2 X 3 X X X 4 X X X X If you use more than one memory module, then make sure to distribute the memory modules over both memory channels (see table). By doing this you use the performance advantages of the dualchannel mode. 22 - English A26361-D1562-Z121-1-6319 Upgrading main memory Memory clock pulse speed The memory clock pulse speed is affected by the chipset and processor system bus (PSB). The table shows the memory speed in dependence on the Processor System Bus. System bus (MHz) DDR400 (MHz) DDR333 (MHz) DDR266 (MHz) 800 533 400 Installing a memory module 400 333 266 320 333 266 266 266 266 2 2 Ê Ê Ê Push the holders on each side of the memory slot outwards. [. . . ] Abort the normal Flash BIOS update by answering the question about whether you want to perform the update with n Ê To carry out the Flash BIOS update for the processor, enter: flashbioË/p6 Check date and time settings The system date and time are invalid. Set the current date and time in the Main menu of the BIOS Setup. CPU ID 0x failed Switch the server off and on again. If the message is still displayed, go into the BIOS setup and set the corresponding processor to Disabled in the Server - CPU Status menu; please contact your sales outlet or customer service centre. CPU mismatch detected You have replaced the processor or changed the frequency setting. Confirm this change by running the BIOS Setup and exiting it again. Diskette drive A error Diskette drive B error Check the entry for the diskette drive in the Main menu of the BIOS Setup. [. . . ]