User manual FUJITSU SIEMENS SCENIC PRO D7/M7

[. . . ] Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Siemens AG D-81730 München Bestell-Nr. /Order No. : A26361-D969-Z120-8-7619 Printed in the Federal Republic of Germany AG 1198 11/98 A26361-D969-Z120-1-7619 Introduction Important notes System board D969 Settings in BIOS Setup Settings with switch block Add-on modules Technical Manual Error messages Index November 1998 edition Creative is a registered trademark, Sound Blaster 16 and VIBRA 16C are trademarks of Creative Technology Ltd. Intel and Pentium are registered trademarks and OverDrive is a trademark of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. [. . . ] controller) or an ISA board. VGA Interrupt - Assigning PCI-VGA interrupt assigns PCI interrupt to the screen controller on the built-in PCI board. If you have not defined any other interrupt with PCI Interrupt Mapping, IRQ9 is assigned. Enabled Disabled The interrupt is assigned to the screen controller on the built-in PCI board (default entry). The interrupt can be used for other add-on boards. 28 A26361-D969-Z120-8-7619 Advanced - Advanced system configuration PCI Device, Slot #n: Default Latency Timer Settings in BIOS Setup specifies the lowest number of clock cycles in which a PCI master board can be active at the PCI bus; n stands for the number of the PCI slot. For the change to take effect, you must switch your device off and then on again after the BIOS Setup has terminated. The entry in the corresponding field for PCI Device, Slot #n: Latency Timer is ignored The value predefined by the PCI board is ignored. The value set in the relevant field of PCI Device, Slot #n: Latency Timer determines the number of clock cycles. No PCI Device, Slot #n: Latency Timer Requirement: The relevant field of PCI Device, Slot #n: Default Latency Timer must be set to No. The field defines the lowest number of clock cycles in which a burst can be transferred on the PCI bus. 0000h to 0280h Number of clock cycles (default entry = 0040h). Advanced System Configuration calls the submenu in which you can make additional settings. Phoenix BIOS Setup Advanced Advanced System Configuration ISA Memory Gap: Parity Mode: System Performance: Feature Connector: [Disabled] [Disabled] [Fast] [Disabled] Item Specific Help F1 Help ESC Exit Select Item Select Menu -/+ Enter Change Values Execute Command F9 Setup Defaults F7 Previous Values Example for submenu Advanced System Configuration A26361-D969-Z120-8-7619 29 Settings in BIOS Setup ISA Memory Gap Advanced - Advanced system configuration inserts a contiguous ISA memory area of 1 Mbyte into the main memory area of 15 to 16 Mbytes. The ISA memory area is not inserted (default). Parity Mode - DRAM Parity Check Determines whether a parity check is carried out in the case of DRAM modules. If the system BIOS detects that at least one DRAM module does not have a parity bit, the parity check is generally disabled. System Keyboard When the PC is started, the system password enables the operating system to be booted. When the PC is started, the operating system is booted and the keyboard and mouse are locked. The system password unlocks the keyboard and mouse. System Load This field specifies the drive from which the operating system can be loaded. Standard Diskette Lock The operating system can be loaded from floppy disk or hard disk (default entry). The operating system can only be loaded from hard disk. Setup Prompt - Setup message specifies whether the setup message Press F2 to enter SETUP is displayed when the system is rebooted. Enabled Disabled The setup message Press F2 to enter SETUP is displayed when the system is started (default entry). The setup message is not displayed. 34 A26361-D969-Z120-8-7619 Security menu - Setting up the security features Settings in BIOS Setup Virus Warning This field checks the boot sectors of the hard disk drive to see if any changes have been made since the previous system startup. If they have been changed and the reason for this is unknown, a program for finding computer viruses should be loaded. Enabled If the boot sector has been changed since the previous system startup (e. g. The warning stays on the screen until you acknowledge the changes with Confirm or deactivate the function (Disabled). The boot sectors are not checked (default entry). Confirm Disabled Diskette Write This field is used to enable and disable floppy disk write-protection. [. . . ] Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Keyboard error nn Frigör den angivna tangenten (nn är tangentens hexadecimalkod). A26361-D969-Z120-8-7619 67 Felmeddelanden Monitor type does not match CMOS - RUN SETUP Korrigera inställningarna för bildskärmtypen i menyn Main i BIOS-Setup menyn. Operating system not found Kontrollera inställningarna för hårddisken och diskettenheten i menyn Main i BIOS-Setup-menyn. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. [. . . ]