User manual FUJITSU SIEMENS SCENIC PRO C6/D6/M6

[. . . ] Please contact: · one of our IT Service Shops · your sales partner · your sales office The addresses of your service partners are contained in the guarantee booklet or in the service address booklet. The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. siemens. com/pc . . . Siemens AG User Documentation Department ICP CS BS2 OS ID4 Otto-Hahn-Ring 6 D-81730 München Your training needs? The Siemens Training Centers offer you a wide range of training courses in information technology and on IT products and other subjects - onsite near to your workplace or offsite at one of our training centers. Contact us for information on consulting, course schedules and selfstudy material Either fax (which is the fastest way): Fax: . . 49 89 636-42945 Or write to: Siemens AG Training Center, Beratungsservice D-81730 München System board D983 Dieses Handbuch wurde auf Recycling-Papier gedruckt. [. . . ] Low-speed drives are preferred for the second (secondary) connector (e. g. The two IDE hard disk controller are disabled. Mouse Controller This field is used to enable and disable the built-in mouse controller on the system board. Enabled The mouse controller is enabled (default entry)- IRQ 12 is used. Audio Controller This field sets the base address for the audio controller on the system board or disables the audio controller. Enabled The system BIOS determines which system resources (interrupts, addresses, DMAs) are occupied (default entry). USB Controller switches the USB controller (Universal Serial Bus) of the system board on or off. Enabled The system BIOS determines which system resources (interrupts, addresses) are occupied. Disabled The USB controller is disabled (default entry). 26 A26361-D983-Z120-7-7619 Advanced - System settings Settings in BIOS Setup PCI Configuration calls the submenu in which you can make the settings for the PCI slots. Phoenix BIOS Setup Advanced PCI Configuration PCI PCI PCI PCI Interrupt Interrupt Interrupt Interrupt Mapping Mapping Mapping Mapping INTA#: INTB#: INTC#: INTD#: [Auto] [Auto] [Auto] [Auto] [Disabled] [Yes] [0040] [Yes] [0040] [Yes] [0040] -/+ Enter Change Values Execute Command F9 Setup Defaults F7 Previous Values Item Specific Help VGA Interrupt: PCI Device, Slot #1 Default Latency Timer: Latency Timer: PCI Device, Slot #2 Default Latency Timer: Latency Timer: PCI Device, Slot #3 Default Latency Timer: Latency Timer: F1 Help ESC Exit Select Item Select Menu Example for submenu PCI Configuration A26361-D983-Z120-7-7619 27 Settings in BIOS Setup Advanced - System settings PCI Interrupt Mapping INTx# defines which PCI interrupt is switched to which ISA interrupt. For the change to take effect, you must switch your PC off and then on again after the BIOS Setup has terminated. If you use a setting other than Auto, the Plug&Play functionality of the system BIOS for PCI boards is deactivated. The PCI interrupts INTA#, INTB# and INTC# are assigned as follows: PCI slot 1 = INTA#, PCI slot 2 = INTB#, PCI slot 3 = INTC# Auto The PCI interrupts are assigned automatically in accordance with the Plug&Play guidelines (default entry). Disabled No PCI interrupt is used for the PCI board in the assigned PCI slot. IRQ03, IRQ04, IRQ05, IRQ06, IRQ07, IRQ09, IRQ10, IRQ11, IRQ12, IRQ14, IRQ15 The PCI interrupt is switched to the selected ISA interrupt. You may not select an ISA interrupt that is used by a component on the system board (e. g. VGA Interrupt assigns PCI interrupt to the monitor controller on the built-in PCI module. If you have not defined any other interrupt with PCI Interrupt Mapping, IRQ9 is assigned. Enabled The interrupt is assigned to the monitor controller on the built-in PCI module. Disabled The interrupt can be used for other add-on modules (default entry). 28 A26361-D983-Z120-7-7619 Advanced - System settings Settings in BIOS Setup PCI Device, Slot #n: Default Latency Timer specifies the lowest number of clock cycles in which a PCI master module can be active at the PCI bus. For the change to take effect, you must switch your PC off and then on again after the BIOS Setup has terminated. The entry in the corresponding field for PCI Device, Slot #n: Latency Timer is ignored. The value set in the corresponding field for PCI Device, Slot #n: Latency Timer determines the number of clock cycles. PCI Device, Slot #n: Latency Timer Requirement: The corresponding field for PCI Device, Slot #n: Default Latency Timer must be set to No. The field defines the lowest number of clock cycles in which a burst can be transferred on the PCI bus. [. . . ] Kontrollera diskettenhetens anslutningar. Extended RAM Failed at offset: nnnn Failing Bits: nnnn System RAM Failed at offset: nnnn Starta upp PCn på nytt. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Fixed Disk 0 Failure Fixed Disk 1 Failure Fixed Disk Controller Failure Kontrollera inställningarna för hårddisken i menyn Main i BIOS-Setup-menyn. Kontrollera hårddiskens anslutningar och insticksbryggorna. Incorrect Drive A - run Setup Incorrect Drive B - run Setup Korrigera inställningen för diskettenheten i menyn Main i BIOS-Setup-menyn. Invalid NVRAM media type Starta upp PCn på nytt. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Invalid System configuration Data Ställ in värdet Yes för Reset Configuration Data i menyn Advanced i BIOS-Setupmenyn. Keyboard controller error Anslut ett annat tangentbord. [. . . ]