User manual FUJITSU SIEMENS SCENIC PRO C5/D5/M5

[. . . ] BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com (Services & Support). Dieses Handbuch wurde auf Recycling-Papier gedruckt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1944-Z120-1-7419 Ausgabe/Edition 1 Printed in the Federal Republic of Germany AG 1104 11/04 A26361-D1944-Z120-1-7419 English Mainboard D1944 Technical Manual Ausgabe November 2004 November 2004 edition Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. [. . . ] Therefore the micro controller protects your PC reliably against overheating and loss of data or even damage of the processor. In addition, the microcontroller offers monitoring of, for example, system voltages (12 V, 5 V, CMOS), opening of the case and a watchdog function. Silent Drives Hard disks and optical drives (CD-ROM, CD-RW, DVD etc. ) are besides the fans some of the greatest sources of noise in a PC. 1 A) / 12 V (4 Pin) Fan sense Fan Control Processor power supply 3 1 Pin 1 2 Signal GND GND Pin 3 4 Signal +12V +12V A26361-D1944-Z120-1-7419, edition 1 English - 7 Interfaces and connectors Power supply BTX (ATX compatible) 1 13 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Signal +3. 3 V (P3V3P) +3. 3 V (P3V3P) GND +5V (VCC) GND +5V (VCC) GND Powergood (high asserted) +5 V Auxiliary (VCC Aux) +12 V (P12VP) +12 V (P12VP) Pin 13 14 15 16 17 18 19 20 21 22 23 24 Signal +3. 3 V (P3V3P) -12 V (P12VN) GND PS on (low asserted) GND GND GND -5 V (P5VN) +5 V (VCC) +5 V (VCC) +5 V (VCC) GND USB - dual channel 1 11 2 12 Pin 1 3 5 7 9 11 Signal Key VCC C Data negative C Data positive C GND Key Pin 2 4 6 8 10 12 Signal Chipcardreader on VCC D Data negative D Data positive D GND not connected 8 - English A26361-D1944-Z120-1-7419, edition 1 Interfaces and connectors CD/AUX 1 Pin 1 2 3 4 Signal Left audio input Audio GND Audio GND Right audio input 1 Power control (system monitoring) Pin 1 2 3 4 5 6 7 8 Signal Power Guard Control PS FAN Control PS FAN Sense Serial ATA (internal) 1 Pin 1 3 5 7 Signal GND Transmit data negative Receive data negative GND Pin 2 4 6 Signal Transmit data positive GND Receive data positive A26361-D1944-Z120-1-7419, edition 1 English - 9 Interfaces and connectors System speaker (internal) 1 Pin 1 3 Signal Speaker + Key Pin 2 4 Signal GND Speaker - Intrusion 1 Pin 1 2 3 Signal GND Case open (low asserted) Intrusion switch present (low asserted) 10 - English A26361-D1944-Z120-1-7419, edition 1 Jumper settings Jumper settings Your mainboard is equipped with jumpers. The positions of the jumpers are shown on page "Cover". Jumper for system and BIOS Setup password Setting via jumpers Pin pair 1 inserted = Skipping system and BIOS Setup password Pin pair 2 inserted = System BIOS recovery Any other setting = State of supply; jumper has no function 1 2 i The clock frequency of the processor is set automatically. Skipping system and BIOS Setup password - pinpair 1 Pinpair 1 enables skipping the system and BIOS Setup password. Inserted Not inserted System and BIOS Setup password are skipped when the device is switched on and may be changed. System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - pinpair 2 Pinpair 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need an external USB floppy disk drive and a Flash BIOS floppy disk (see chapter "BIOS update") or a configured removable USB medium. Inserted A: The System BIOS executes from a configured removable USB medium (e. g. B: The System BIOS executes from the external USB floppy disk drive and the inserted "Flash BIOS floppy disk" restores the System BIOS on the mainboard. Not inserted Normal operation (default setting). A26361-D1944-Z120-1-7419, edition 1 English - 11 Add-on modules / Upgrading Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter!The assignment of the PCI interrupts to the PCI IRQ Lines is shown in the following table: Controller or slot INT On board controller PCI USB 1. 1 INT LINE USB 2. 0 SMBus 1 st Mechanical slot 1 AC97 / HD Audio HD Audio 1 - PCI slot AC97 1 (A) 2 (B) 3 (C) 4 (D) 5 (E) 6 (F) 7 (G) 8 (H) X X - X - X - X X - X - X - X - PCIe x1 2 nd 3 rd 4 th 1 - - - - LAN D A B C - - D C B A - - - - - Use the first PCI slots that have a single PCI IRQ Line (no IRQ sharing). If you must use another PCI slot with IRQ sharing, check whether the expansion card properly supports IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. 18 - English A26361-D1944-Z120-1-7419, edition 1 Add-on modules / Upgrading Replacing the lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion!The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. They must be disposed of in accordance with local regulations concerning special waste. The plus pole must be on the top! The lithium battery holder exists in different designs that function in the same way. 2 3 3 2 1 3 Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the holder (1). Insert a new lithium battery of the same type into the socket (3). A26361-D1944-Z120-1-7419, edition 1 English - 19 Add-on modules / Upgrading BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software. Where can I obtain BIOS updates? The BIOS updates are available on the Internet at www. fujitsu-siemens. com. How does a BIOS update work? You have two ways of doing this: 1. BIOS update under DOS with bootable BIOS update floppy disk - brief description Download the update file from out website to your PC. [. . . ] Previous boot incomplete - Default configuration used By pressing function key F2 you can check and correct the settings in BIOS Setup. By pressing function key F1 the system starts with incomplete system configuration. If the message is still displayed, please contact your sales outlet or customer service centre. Real time clock error Call the BIOS Setup and enter the correct time in the Main menu. [. . . ]