User manual FUJITSU SIEMENS SCENIC P300 (I845GV)

[. . . ] Published by Fujitsu Siemens Computers GmbH Order No. : A26361-D1761-Z121-1-7419 Printed in the Federal Republic of Germany AG 0504 05/04 Edition 1 A26361-D1761-Z121-1-7419 Deutsch English Mainboard D1761 Technical Manual May 2004 edition Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt. [. . . ] Drivers A corresponding driver must be installed for the 2, 4 or 6-channel audio mode. If the drive is not installed yet, proceed as described in the chapter "Add-on modules / Upgrading", in the section "Drivers". Connecting loudspeakers The number of loudspeakers connected should match the number of audio channels you select in the driver software. A26361-D1761-Z121-1-7419, Edition 1 English - 9 Internal ports and connectors Using external audio connections Analogue 2-channel audio output 1 2 3 With the 2-channel configuration the functions Line-Out, Line-In and MIC are available. 1 = Line-In (blue) 2 = Line-Out (front channels, green) 3 = MIC (red) Analogue 4-channel audio output 1 2 3 Line-In is converted into the Rear-Out function with the 4-channel configuration. 1 = Line-In (rear channels, blue) 2 = Line-Out (front channels, green) 3 = MIC (red) Analogue 6-channel audio output 1 2 3 Line-In and MIC are converted into the function Line-Out with the 6-channel configuration. 1 = Line-In (rear channels, blue) 2 = Line-Out (front channels, green) 3 = MIC (centre and subwoofer channel, red) i Depending on driver version and operating system the functions may differ from this presentation. If necessary, further information is provided in the respective help system of drivers and software. Selecting settings for 2, 4 or 6-channel audio mode Depending on the driver for the audio mode and from the operating system used, you can configure the audio properties, e. g. with Windows 2000 under Start - Settings - Control Panel - Sounds and Multimedia. 10 - English A26361-D1761-Z121-1-7419, Edition 1 Pin assignment of internal ports Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following. i Some of the following connectors may be optional! Front panel Watch the poling of the LEDs. The positive pole of the connection cables is often indicated with a coloured wire. Power On/Off Reset 1) 3) 1) HD-LED Power On 1) 2) LED 1 2 Recovery Password Speaker 1) Cable is not included in the delivery scope. 2) 2-pin or 3-pin connector possible 3) both connector positions possible Connection Reset Power On/Off HD LED Power On LED Password Recovery Speaker Note Indicates the system state APM or ACPI (see annex, "APM and ACPI system status, energy-saving modes" section). see "Settings with switches and jumpers" chapter see "Settings with switches and jumpers" chapter 0, 5 W at 8 Ohm CD audio input 1 Pin 1 2 3 4 Signal Left CD audio input CD GND CD GND Right CD audio input A26361-D1761-Z121-1-7419, Edition 1 English - 11 Pin assignment of internal ports Audio front panel 1 2 Pin 1 3 5 7 9 Signal Micro input Micro bias Right line output not connected Left line output Pin 2 4 6 8 10 Signal Analogue GND Analogue VCC Right line return Key Left line return If the audio front panel is not used, you must plug jumpers on pin pairs 5/6 and 9/10. USB - dual channel (internal or external via special wire) 1 2 Pin 1 3 5 7 9 Signal VCC C Data negative C Data positive C GND Key Pin 2 4 6 8 10 1 Signal VCC D Data negative D Data positive D GND not connected Fan 1 (CPU) Fan 2 (AUX1) (only for 3 pin fans) Pin 1 2 3 Signal GND Controlled FAN voltage (0V, +6V, . . . Should IRQ sharing be unavoidable, then all involved devices and their drivers must support IRQ sharing. PCI IRQ Lines connect AGP slots, PCI slots and onboard components to the interrupt controller. Which ISA IRQs are assigned to the PCI IRQ Lines is normally automatically specified by the BIOS (see description in "BIOS Setup"). Monofunctional expansions cards: Standard AGP and PCI expansion cards require a maximum of one interrupt, which is called the PCI interrupt INT A. Expansion cards that do not require an interrupt can be installed in any desired slot. Multifunctional expansion cards or expansion cards with integrated PCI-PCI bridge: These expansion cards require up to four PCI interrupts: INT A, INT B, INT C, INT D. How many and which of these interrupts are used is specified in the documentation provided with the card. The assignment of the PCI interrupts to the PCI IRQ Lines is shown in the following table: USB 2, 0 Modem Audio LAN IDE 1 st 2 n d 3 rd AGP Chips et INT LINE Controller or slot INT Mechanical slot On board controller 1 2 3 4 USB 1, 1 AC97 PCI slot 1 B C D A - 2 C D A B - 3 D A B C - 1 (A) 2 (B) 3 (C) 4 (D) 5 (E) 6 (F) 7 (G) 8 (H) + - + - + - + + - + - + - + - A B - Use the first PCI slots that have a single PCI IRQ Line (no IRQ sharing). If you must use another PCI slot with IRQ sharing, check whether the expansion card properly supports IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. A26361-D1761-Z121-1-7419, Edition 1 English - 21 Replacing the lithium battery Replacing the lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion!The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. They must be disposed of in accordance with local regulations concerning special waste. [. . . ] Abort the normal Flash BIOS update by answering the question about whether you want to perform the update with n To carry out the Flash BIOS update for the processor, enter: flashbioË/p6 Check date and time settings The system date and time are invalid. Set the current date and time in the Main menu of the BIOS Setup. CPU ID 0x failed Switch the server off and on again. If the message is still displayed, go into the BIOS setup and set the corresponding processor to Disabled in the Server - CPU Status menu; please contact your sales outlet or customer service centre. CPU mismatch detected You have replaced the processor or changed the frequency setting. Confirm this change by running the BIOS Setup and exiting it again. Diskette drive A error Diskette drive B error Check the entry for the diskette drive in the Main menu of the BIOS Setup. [. . . ]