User manual FUJITSU SIEMENS SCENIC N320 (SIS661+)

[. . . ] Gesellschaft für Technik-Dokumentation mbH www. cognitas. de Intel, Pentium and Celeron are registered trademarks and MMX and OverDrive are trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. Magic Packet is a registered trademark of Advanced Micro Devices, Inc. [. . . ] This symbol means that you must press the Enter key. Texts in this typeface are screen outputs. Texts in this bold typeface are the entries you make via the keyboard. "Quotation marks" indicate names of chapters and terms that are being emphasized. Important notes Store this manual close to the device. If you pass on the device to third parties, you should also pass on this manual. Be sure to read this page carefully and note the information before you open the device. You cannot access the components of the system board without first opening the device. How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please note the information provided in the chapter "Safety" in the Operating Manual of the device. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the chapter , , dd-on modules" - , , Replacing the A lithium battery". ! A26361-D1192-Z120-2-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual of the receiving device. Connecting cables for peripherals must be adequately insulated to avoid interference. ! i Components can become very hot during operation. Make sure you do not touch components when making extensions to the system board. There is a danger of burns!1 = Yellow indicator 2 = Green indicator 1 2 Green Yellow a connection exists (e. TM a Magic Packet is being received. 8 - English A26361-D1192-Z120-2-7419 Features PCI bus interrupts The following table shows which PCI bus interrupts on the system board are assigned. PCI bus interrupt B, C, D, A C, D, A, B D, A, B, C A, B, C, D B, C, D, A A, B D D A B B Component on system board: PCI bus slot 1 PCI bus slot 2 PCI bus slot 3 PCI bus slot 4 PCI bus slot 5 AGP slot USB controller LAN controller Graphics processor SMBus AC'97 Audio A26361-D1192-Z120-2-7419 English - 9 Settings with switches and jumpers Settings with switches and jumpers RIMM 4 RIMM 3 RIMM 2 RIMM 1 4321 AGP Pro ON PCI 4 PCI 1 PCI 2 PCI 3 PCI 5 Switch 1 = must be set to off Switch 2 = System BIOS recovery Switch 3 = Write-protection for floppy disk Switch 4 = must be set to off i The clock frequency of the processor is set automatically. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service center). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the system board. Normal operation (default setting). Write protection for floppy disks - switch 3 Switch 3 is used to define whether floppy disks can be written or deleted in the floppy disk drive. To write and delete floppy disks, the write-protection inBIOS Setup must be disabled (in menu Security, the field Diskette Write must be set to Enabled). Read, write and delete floppy disks is possible (default setting). 10 - English A26361-D1192-Z120-2-7419 CNR Add-on modules Add-on modules ! For all steps described in this chapter exit the suspend mode before switching off the device and then pull the power plug out of the power outlet!All PCI slots support 3. 3 V main and auxiliary voltages. 6 5 4 3 2 RIMM 4 RIMM 3 RIMM 2 RIMM 1 AGP Pro PCI 1 PCI 4 1 PCI 2 PCI 3 PCI 5 9 1= 2= 3= 4= 5= Slot for processor with heat sink Location bank 0 for main memory Location bank 1 for main memory Location bank 0 for main memory Location bank 1 for main memory 6= 7= 8= 9= 8 7 Lithium battery CNR slot PCI slots 1, 2, 3, 4, 5 AGP Pro slot i PCI slots support 3. 3 V / 5 V main voltage and 3. 3 V auxiliary voltage. CNR A26361-D1192-Z120-2-7419 English - 11 Add-on modules Installing / removing processor 3 2 4 5 1 A Ê Ê Ê Press the retainers in the direction of the arrow (1) and (2) and tilt it upwards. Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). ! Ê Ê Ê The angled corner of the processor may be covered by the heat sink. In this case let yourself be guided by the marking in the rows of pins on the underside of the processor. Apply the heat transfer compound evenly on the underside of the heat sink(approx. Tilt the retainers downwards and press in the direction of the arrow(5). 12 - English A26361-D1192-Z120-2-7419 Add-on modules Upgrading main memory These slots are suitable for 128 to 512 Mbyte RDRAM memory modules of the RIMM format. The permissible total size of the main memory is 2Gbyte. [. . . ] If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage. You may find further information in the supplied description of the network board. i Replacing the lithium battery ! Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the trashcan. It must be disposed of in accordance with local regulations concerning special waste. [. . . ]