User manual FUJITSU SIEMENS SCENIC EDC

[. . . ] Copyright ã Fujitsu Siemens Computers GmbH 2000 Intel, Pentium and Celeron are registered trademarks and MMX and OverDrive are trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. Magic Packet is a registered trademark of Advanced Micro Devices, Inc. [. . . ] Supplementary information, remarks and tips follow this symbol. Texts which follow this symbol describe activities that must be performed in the order shown. This symbol means that you must press the Enter key. Texts in this typeface are screen outputs. Texts in this bold typeface are the entries you make via the keyboard. "Quotation marks" indicate names of chapters and terms that are being emphasized. Important notes Store this manual close to the device. If you pass on the device to third parties, you should also pass on this manual. Be sure to read this page carefully and note the information before you open the device. You cannot access the components of the system board without first opening the device. How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please note the information provided in the chapter "Safety" in the Operating Manual of the device. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the chapter "Add-on modules" - "Replacing the lithium battery". ! A26361-D1115-Z120-10-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Normal operation (default setting). Write protection for floppy disks - switch 3 Switch 3 is used to define whether floppy disks can be written or deleted in the floppy disk drive. memory modules, AGP and PCI extension boards) are still energized. 4 5 6 7 3 2 1 2 AGP PCI 3 PCI 2 Slot 1 1 1= 2= 3= 4= Slot for processor with heat sink Location bank 1 for main memory Location bank 2 for main memory Lithium battery 5 = AGP slot 6 = PCI slots 1, 2, 3 7 = ISA slot i All PCI slots have bus master capability and support 3. 3 V. 10 - English A26361-D1115-Z120-10-7419 PCI 1 ISA Add-on modules Installing / removing processor Installing the processor i If you wish to upgrade your system with a new processor, the processor bracket on the system board may need to be replaced beforehand. Should it be necessary to replace the bracket, please contact our customer service center. Depending on the design of the processor housing, the heat sink can be moved on the processor and the processor in the bracket. This floating suspension in the installed state ensures reliable contact between the processor and the heat sink. If the heat sink on the processor can be moved, then it must also be possible to move the mounted processor in the bracket. If you replace the processor, grasp the processor housing by the processor and the heat sink. (A) 2 2 (B) 2 1 2 1 1 1 The illustration shows two bracket and processor models. Ê Ê Ê Ê Ê Remove the old processor if necessary. Push the processor down in the bracket and press it into the slot until the clamps (2) to the left and right snap into place. Set the clock frequency of the new processor using switches 5 to 8 of the switch block. If the processor has a temperature sensor or a fan, attach the associated cable to the connector for the temperature sensor or the fan on the system board. Removing the processor Ê Ê If the processor has a temperature sensor or a fan, pull out the associated cable. Press the clamps (2) on either side of the processor slightly inwards (A) or outwards (B) and pull the processor up and out. [. . . ] Lever det brugte batteri tilbage til leverandøren. · · · ADVARSEL Explosionsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. 1 + + 2 + + 3 Ê Ê Lift the contact (1) a few millimeters and remove the battery from its socket (2). Insert a new lithium battery of the same type in the socket (3). A26361-D1115-Z120-10-7419 English - 13 Glossary Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. [. . . ]