User manual FUJITSU SIEMENS SCENIC E300 (I865GV)

[. . . ] BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr. /Order No. : A26361-D1451-Z120-1-6319 Printed in the Federal Republic of Germany AG 0203 02/03 A26361-D1451-Z120-1-6319 Deutsch English Mainboard D1451 Français Technisches Handbuch Technical Manual Ausgabe März 2003 March 2003 edition Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. [. . . ] The positive pole of the connection cables is often indicated with a coloured wire. Power On/Off Message LED1) Sleep LED 1) Power On Sleep 1) HD-LED LED 1) 3) 1) Reset 1 2 SCSI LED Input 1) 2) Speaker 1) Cable is not included in the delivery scope. 2) The same interface 3) 2pin or 3pin connector possible Connection Reset Sleep Power On/Off HD LED SCSI Activity Input Message LED Power On LED I Speaker Sleep LED Note This connection is reserved for future use. Warning: Do not connect to the LED connections of an SCSI controller!Indicates the system state APM or ACPI together with the Sleep LED (see chapter entitled "APM and ACPI system status, energy-saving modes"). 0, 5 W at 8 Ohm Indicates the system state APM or ACPI together with the Power-On LED (see chapter entitled "APM and ACPI system status, energy-saving modes"). Power On LED II 1 3 Pin 1 2 3 Note Power On LED (Anode) Power On LED (Anode) Power On LED (Cathode) Intrusion 1 Pin 1 2 3 Note GND Case open (low asserted) Intrusion switch present (low asserted) 10 - English A26361-D1451-Z120-4-6319 Pin assignment of internal ports USB E/F - dual channel (internal or external via special wire) 1 11 2 12 Pin 1 3 5 7 9 11 Signal Key VCC C Data negative C Data positive C GND Key Pin 2 4 6 8 10 12 Signal Chipcard reader on VCC D Data negative D Data positive D GND Not Connected Fan 2 (system fan - supervised) Pin 1 2 1 Signal GND Controlled Fan voltage (0 V, +6 V . . . 1 A) Fan sense 3 CD-ROM audio 1 Pin 1 2 3 4 Signal Left CD audio input CD GND CD GND Right CD audio input A26361-D1451-Z120-4-6319 English - 11 Pin assignment of internal ports Audio front panel 1 2 Pin 1 3 5 7 9 Signal Micro input Micro bias Right line output NC Left line output Pin 2 4 6 8 10 Signal Analog GND Analog VCC Right line return Key Left line return Audio S/PDIF 1 Pin 1 2 3 Signal VCC SPDIF out GND Processor power supply power supply 3 1 Pin 1 2 Signal GND GND Pin 3 4 Signal +12 V +12 V Fan 1 (system fan - supervised) Pin 1 2 3 Signal 1 GND Controlled Fan voltage (0 V, +6 V . . . 1 A) Fan sense 12 - English A26361-D1451-Z120-4-6319 Pin assignment of internal ports Settings with switches and jumpers The positions of the switches and jumpers are shown on page "Cover". Skipping system and BIOS Setup password - switch 1 Switch 1 enables skipping the system and BIOS Setup password. On Off System and BIOS Setup password are skipped when the device is switched on and may be changed. System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service centre). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the mainboard. How many and which of these interrupts are used is specified in the documentation provided with the card. The assignment of the PCI interrupts to the PCI IRQ Lines is shown in the following table: Onboard controller PCI INT LINE 1 (A) 2 (B) 3 (C) 4 (D) 5 (E) 6 (F) 7 (G) 8 (H) USB 1, 1 1st A 2nd A 3rd A USB 2, 0 A SM Bus A AC97 Audio A Modem A LAN A Graphic A PCI slot 1 A B C D 2 A B C D 3 A B C D - Use the first PCI slots that have a single PCI IRQ Line (no IRQ sharing). If you must use another PCI slot with IRQ sharing, check whether the expansion card properly supports IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion!The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. They must be disposed of in accordance with local regulations concerning special waste. The plus pole must be on the top! 18 - English A26361-D1451-Z120-4-6319 Adding PCI cards The lithium battery holder exists in different designs that function in the same way. 2 3 3 2 1 3 Ê Ê Ê Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the holder (1). Insert a new lithium battery of the same type into the socket (3). A26361-D1451-Z120-4-6319 English - 19 BIOS update BIOS update When should a BIOS update be carried out?Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. [. . . ] Service Processor not properly installed The server management controller has not been correctly installed. If the message is still displayed, please contact your sales outlet or customer service centre. Storage Extension Group = xy Configuration error, x Storage Extensions(s) found, configured are y SE(s). The specified number of storage expansion units (SEs) in the BIOS Setup menu Server - Storage Extensions - Number of connected SE is incorrect. [. . . ]