User manual FUJITSU SIEMENS PRIMERGY RX100 S6 E-STARFAM1 DATASHEET

[. . . ] ENERGY STAR ® Power and Performance Data Sheet PRIMERGY RX100 S6 E-StarFam1 (Dual-Core CPUs) System Characteristics Form Factor Available Processor Sockets Available DIMM Slots / Max Memory Capacity ECC and/or Fully Buffered DIMMs Available Expansion Slots Minimum and Maximum # of Hard Drives Redundant Power Supply Capable? [. . . ] Other Hardware Features / Accessories 1 Yes 8 port SAS RAID Controller DVD-RW supermulti 1 Yes 8 port SAS RAID Controller DVD-RW supermult ENERGY STAR Power and Performance Data Sheet PRIMERGY RX100 S6 E-StarFam1 (Dual-Core CPUs) Page 2 of 2 Power Data Idle Category (1S and 2S only) ENERGY STAR Idle Power Allowance (1S and 2S only) Measured Idle Power (watts) Power at Full Load* (watts) Benchmark / Method Used for Full Load Test Test Voltage and Frequency for Idle and Full Load Test Range of Total Estimated Energy Usage ** (kWh/year) Link to Detailed Power Calculator (if available) Minimum 55W 51, 1 Typical 63W 56, 1 Maximum 95W 71, 5 Category A: Standard Single Installed Processor (1P) Servers 76, 6 82, 9 100, 2 SiSoftware Sandra Engineer 2009. SP3c, . Net Multimedia, Double x1 230V / 50Hz 895 to 1342 983 to 1452 1253 to 1756 http://ts. fujitsu. com/products/standard_servers/e_efficient. html * Note: Full load power represents the sustained, average power at 100% load of the given workload, and does not necessarily represent the absolute peak power or the highest average, sustained power possible for other workloads. ** Note: Estimated kWh/year gives the absolute range of energy use a user could expect from continuous operation (24x365) and ranges from 100% Idle usage to 100% full load operation. The calculation also includes typical data center overhead at a ratio of 1 watt of overhead to every 1 watt of IT load (corresponding to a PUE of 2. 0). Closer approximations may be found by using established power calculators and specific information about the intended operating environment (e. g. , average time at Idle, data center PUE, etc. ). Power and Performance for Benchmark #1 Benchmark #1 Benchmark Used and Type of Workload Avg. Power Measured During Benchmark Run Benchmark Performance Score Power Performance Ratio (perf score/avg. power) Link to Full Benchmark Report (Where Available) Minimum 76, 6W 11, 9MPixels/s 0, 16MPixels/s / W N/A Typical 82, 9W 12MPixels/s 0, 14MPixels/s / W N/A Maximum 100, 2W 12MPixels/s 0, 12MPixels/s / W N/A SiSoftware Sandra Engineer 2009. SP3c, . Net Multimedia, Double x1 Power Saving Features Processor Dynamic Voltage and Frequency Scaling Processor or Core Reduced Power States Power Capping Variable Speed Fan Control Based on Power or Thermal Readings Low Power Memory States Low Power I/O States Liquid Cooling Capability Enabled on Shipment End-User Enabling Required x x x Power and Temperature Measurement and Reporting Input Power Available & Accuracy? [. . . ] Airflow at Nominal Fan Speed (CFM) at Nominal Temp. Minimum 82 13 75m3/h 18m3/h Typical 91 16 75m3/h 18m3/h Maximum 104 19 75m3/h 18m3/h * References: ASHRAE Extended Environmental Envelope Final August 1, 2008 Thermal Guidelines for Data Processing Environments, ASHRAE, 2004, ISBN 1-931862-43-5 Peak temperature is defined as 35 °C, Nominal Temperature is defined as 18 - 27 °C [. . . ]