User manual FUJITSU SIEMENS PCD-5H/PCI

[. . . ] Contact us for information on consulting, course schedules and selfstudy material Either fax (which is the fastest way): Fax: ++49(89) 636-42945 Or write to: Siemens Nixdorf Informationssysteme AG Training Center, Beratungsservice D-81730 München Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Adjust it so that your hand is in a comfortable relaxed position when using the mouse. A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 16 17 Preparation for use and operation Connecting devices Connecting devices Preparation for use and operation Connecting the mouse to the PS/2 or serial port You should connect a mouse with a round PS/2 connector to the PS/2 mouse port, or a serial mouse to the serial port of the system unit. It may be necessary to select a specific mouse driver in the operating system (see operating system documentation). Connecting loudspeakers, a microphone and audio devices i Only on a system unit with audio functionality. i Only one mouse may be connected to the PC (keyboard and system unit). If you attach a serial mouse, you can disable the mouse controller in the BIOS Setup in order to free the IRQ12 for a different application. If the mouse controller is disabled, you will not be able to operate either the supplied mouse nor a mouse connected to the PS/2 mouse port. Only active loudspeakers may be used. The external microphone must be a dynamic microphone or a condenser microphone. Connect the cable of the external loudspeakers to the audio output of the system unit. Connect the cable of the external microphone to the microphone port of the system unit. mixer, stereo system) to the audio input of the system unit. Connecting devices with serial or parallel ports Connect the data cable to the external device. Connect the data cable of the external device to the appropriate port on the system unit. Connecting a joystick Connect the data cable of the joystick to the Game/Midi port of the system unit. i Most devices that you connect to the serial or parallel port require special drivers. MS-Windows already includes many drivers but if the driver you need is not on the hard disk please install it from the floppy disk supplied with the device or with the application program. If you need to change the default settings of the serial or parallel port (e. Generate the utility and driver diskettes using the batch files in the \PROGS\DISKS directory and label them. The main switch and ON/OFF switch do not cut off power voltage from the system unit. To cut off the power supply, you must pull out the power plug. Switching the PC ready-to-operate by means of software You can put your PC into ready-to-operate mode in Windows 95 choosing Shut down in the Start menu or using the DeskOff program: Prerequisite: Your system must support switching off with software and this functionality must be enabled in BIOS-Setup (Soft Power OFF - Enabled). Switching on the PC Switch on the monitor (see the Operating Manual of the monitor). Use the main switch on the rear of system unit to switch the system unit on. Exit MS-Windows (choosing Shut down in the Start menu). The PC switches to the mode which was active when it was last switched off: If the Power ON display on the front of the system unit lights up orange, press the ON/OFF switch on the front of the system unit. 24 The system unit is ready-to-operate, and the the Power ON display lights up orange. A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 25 Preparation for use and operation Connecting a MIDI Connecting a MIDI Preparation for use and operation Connecting a MIDI i You need a Game/MIDI port and a commercially available MIDI interface box or Soundblaster-compatible MIDI adapter cable. Connect the MIDI output of your keyboard to the MIDI input of the MIDI interface box. Connect the MIDI input of your keyboard to the MIDI output of the MIDI interface box. Switch on the device. Recording a MIDI file Press the Record button. Save the MIDI file with File - Save. Playing back a MIDI file Press the Play button. You must now also change the basic configuration of your system accordingly. Enable the MIDI interface with: Start - Settings - Control Panel - System iconDevice-Manager index tab. Select the Resources index tab under Sound, video and game controllers for the setting Creative Labs Sound Blaster 16 or AWE 32. Disable the setting Disable MIDI input (empty checkbox) in the menu item Setup - MIDI drivers. [. . . ] If you remove the drive again later, you will have to reinstall the covers. 56 A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 57 System expansions Installing and removing drives Installing and removing drives System expansions Removing an accessible drive 2 1 3 1 Press the metal plate into place on the inside of the appropriate location. Remove the two or four screws (1). Slide the drive out of its location so that you can pull the cables easily. Take the drive completely out of its location (3). Press the drive cover into place until it engages. 58 A26361-K407-Z111-2-7619 A26361-K407-Z111-2-7619 59 System expansions Installing and removing drives Installing and removing drives System expansions Changing the floppy disk drive Remove the bottom cover (see "Installing and removing boards"). Pull the Game/Midi connector from the system board (see the Technical Manual of the system board). 1 2 1 Remove the screws that fix the floppy disk drive to the carrier (1) and take the drive out of the carrier (2). 2 Pull all cable connectors from the floppy disk drive. 2 1 2 1 3 Place the new floppy disk drive in the carrier (1) and fasten it using the screws you removed earlier (2). 60 Remove the screw (1). [. . . ]