User manual FUJITSU SIEMENS ESPRIMO EDITION P2500

[. . . ] Your sales outlet The latest information on our products, tips, updates, etc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. [. . . ] If the drive is not installed yet, proceed as described in the chapter "Add-on modules / Upgrading", in the section "Drivers". Connecting loudspeakers The number of loudspeakers connected should match the number of audio channels you select in the driver software. Line-In is converted into the Rear-Out function with the 4-channel configuration. Line-In and MIC are converted into the function Line-Out with the 6-channel configuration. Depending on driver version and operating system the functions may differ from this presentation. If necessary, further information is provided in the respective help system of drivers and software. Depending on the driver for the audio mode and from the operating system used, you can configure the audio properties, e. The positive pole of the connection cables is often indicated with a coloured wire. Note Connector for reset switch Connection for ATX On/Off switch Indicates HDD (hard disk) activity Indicates the system state APM or ACPI see "Settings with switches and jumpers" chapter see "Settings with switches and jumpers" chapter Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Signal GND FDHDIN (low asserted) GND not connected Key not connected GND Index (low asserted) GND Motor A Enable (low asserted) GND Drive B Select (low asserted) GND Drive A Select (low asserted) GND Motor B Enable (low asserted) GND Pin 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Signal Step DIR (low asserted) GND Step Pulse (low asserted) GND Write Data (low asserted) GND Write Enable (low asserted) GND Track 0 (low asserted) GND Write Protect (low asserted) GND Read Data (low asserted) GND Side 1 Select (low asserted) GND Disk Change (low asserted) Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Reset drive (low asserted) Data 7 (high asserted) Data 6 (high asserted) Data 5 (high asserted) Data 4 (high asserted) Data 3 (high asserted) Data 2 (high asserted) Data 1 (high asserted) Data 0 (high asserted) GND DRQ (high asserted) I/O write (low asserted) I/O read (low asserted) I/O ready (low asserted) DAK (low asserted) IRQ (high asserted) ADR 1 (high asserted) ADR 0 (high asserted) CS 1 (low asserted) IDE-LED (low asserted) Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal GND Data 8 (high asserted) Data 9 (high asserted) Data 10 (high asserted) Data 11 (high asserted) Data 12 (high asserted) Data 13 (high asserted) Data 14 (high asserted) Data 15 (high asserted) Key GND GND GND Cable select GND not connected ATA66 Detect (low asserted) ADR 2 (high asserted) CS 3 (low asserted) GND Setting via control-panel plug connector Pin pair A inserted = Skipping system and BIOS Setup password Pin pair B inserted = System BIOS recovery Pin pair C inserted = factory setting On / inserted System and BIOS Setup password are skipped when the device is switched on and may be changed. Off / not inserted System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - pinpair B Pinpair B enables recovery of the old system BIOS after an attempt to update has failed. To restore the old BIOS you need a Flash BIOS Diskette (see "BIOS update" chapter). Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter!Technical data Intel Pentium 4 with 533 or 800 MHz front side bus in the LGA775 design (Value FMB). Celeron with 533 MHz Front Side Bus in the LGA775 design A current list of the processors supported by this mainboard is available on the Internet at: www. Even minor soiling such as grease from the skin can impair the processor's operation or destroy the processor. Place the processor in the socket with extreme care, as the spring contacts of the socket are very delicate and must not be bent. Insert the new processor in the socket so that the marking of the processor is aligned with the marking on the socket (a). Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it. Please note that, depending on the heat sink used, different heat sink mounts are required on the mainboard. [. . . ] Invalid System Configuration Data - run configuration utility Press F1 to resume, F2 to Setup This error message may be displayed if the machine was switched off during system start-up. If the message is still displayed, please contact your sales outlet or customer service centre. If the message is still displayed, please contact your sales outlet or customer service centre. One or more RDRAM devices are not used One or more RDRAM devices have bad architecture/timing One or more RDRAM devices are disabled Contact your system administrator or contact our customer service centre. [. . . ]