User manual FUJITSU SIEMENS D1740 TECHNICAL MANUAL

[. . . ] answers Mainboard D1740 English 2 Technical Manual Sie haben . . . . . . Wenden Sie sich bitte an: · Ihren zuständigen Vertriebspartner · Ihre Verkaufsstelle Aktuelle Informationen zu unseren Produkten, Tipps, Updates usw. finden Sie im Internet: http://www. fujitsu-siemens. com oder http://www. fujitsu-siemens. com/mainboards Are there . . . . . . Please contact: · your sales partner · your sales outlet The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com or http://www. fujitsu-siemens. com/mainboards Vous avez . . . . . . des questions techniques ou des problèmes ? [. . . ] If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it. Please note that, depending on the heat sink used, different heat sink mounts are required on the mainboard. i If a counter-plate is mounted on the underside of the mainboard for reinforcement, no heat sinks of the type "Intel Boxed" may be used. When using an "Intel Boxed" heat sink, the mainboard must be converted. This conversion set is either included with the mainboard or is available separately. If no counter-plate is mounted, you can use both "Intel Boxed" heat sinks and standard heat sinks. If you use the "Intel Boxed" heat sink, the mainboard will bend due to the high pressure of the retaining clips. Depending on the configuration variant, you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it. Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard. A26361-D1740-Z120-1-6319, Edition: 3 English - 17 Installing and removing processors Upgrading main memory Technical data Technology: Size: Granularity: DDR 200, DDR 266 or DDR 333 unbuffered DIMM modules 184-Pin; 2. 5 V; 64 Bit, no ECC 128 Mbytes up to 2 Gbyte DDR-SDRAM 128, 256, 512 or 1024 Mbyte for one socket A current list of the memory modules recommended for this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2, 5 V memory modules. DDR- DIMM memory modules must meet the PC1600 (DDR 200), the PC2100 (DDR 266) or the PC2700 (DDR 333) specification. Installing a memory module 2 2 Push the holders on each side of the memory slot outwards. At the same time flip the lateral holders upwards until the memory module snaps in place (2). 18 - English A26361-D1740-Z120-1-6319, Edition: 3 Adding PCI cards Removing a memory module 1 1 Push the clips on the right and left of the memory slot outward (1). Pull the memory module out of the memory slot (2). Adding PCI cards Technical data: 32 bit / 33 MHz PCI slots 5 V and 3. 3 V supply voltage 3. 3 V auxiliary voltage PCI bus interrupts - Selecting correct PCI slot i To achieve optimum stability, performance and compatibility, avoid the multiple use of ISA IRQs or PCI IRQ Lines (IRQ sharing). Should IRQ sharing be unavoidable, then all involved devices and their drivers must support IRQ sharing. PCI IRQ Lines connect AGP slots, PCI slots and onboard components to the interrupt controller. Which ISA IRQs are assigned to the PCI IRQ Lines is normally automatically specified by the BIOS (see description in "BIOS Setup"). Monofunctional expansions cards: Standard AGP and PCI expansion cards require a maximum of one interrupt, which is called the PCI interrupt INT A. Expansion cards that do not require an interrupt can be installed in any desired slot. A26361-D1740-Z120-1-6319, Edition: 3 English - 19 Adding PCI cards Multifunctional expansion cards or expansion cards with integrated PCI-PCI bridge: These expansion cards require up to four PCI interrupts: INT A, INT B, INT C, INT D. How many and which of these interrupts are used is specified in the documentation provided with the card. The assignment of the PCI interrupts to the PCI IRQ Lines is shown in the following table: Onboard controller PCI INT LINE 1 (A) 2 (B) 3 (C) 4 (D) 5 (E) 6 (F) 7 (G) 8 (H) USB 1, 1 1st A 2nd A 3rd A USB 2, 0 A SM Bus A AC97 Audio A Modem A LAN A Graphic A PCI slot 1 A B C D 2 A B C D 3 A B C D - Use the first PCI slots that have a single PCI IRQ Line (no IRQ sharing). If you must use another PCI slot with IRQ sharing, check whether the expansion card properly supports IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on this PCI IRQ Line must also support IRQ sharing. Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. [. . . ] Check how many SEs within the group are connected at the server and change the setting in BIOS Setup. xy = Group number x = Number of SEs found on the communication bus y = Number of SEs entered in Number of connected SE k1, k2 . . . = Device ID of the storage extensions found 30 - English A26361-D1740-Z120-1-6319, Edition: 3 DOS error messages System battery is dead - Replace and run SETUP Replace the lithium battery on the mainboard and redo the settings in the BIOS Setup. System Cache Error - Cache disabled Switch the device off and on again. [. . . ]