User manual FRIGIDAIRE ELECTRIC RANGES WITH ES 540 SERVICE DATASHEET
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FRIGIDAIRE ELECTRIC RANGES WITH ES 540. We hope that this FRIGIDAIRE ELECTRIC RANGES WITH ES 540 user guide will be useful to you.
Manual abstract: user guide FRIGIDAIRE ELECTRIC RANGES WITH ES 540SERVICE DATASHEET
Detailed instructions for use are in the User's Guide.
[. . . ] SERVICE DATA SHEET
Electric Range with ES 540 Electronic Oven Control NOTICE - This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The manufacturer cannot be responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet. [. . . ] · All safety grounds (both internal and external) are correctly and securely reassembled. Oven Calibration Set the electronic oven control for normal baking at 350°F. While in a non-cooking mode, press and hold the BAKE key pad for 6 seconds. The current calibration offset (temperature adjustment) should appear in the temperature display. Use the number key pads (0-9) to enter the desired amount of adjustment (up to 35°F). Press the CLEAN key pad to change the sign of the adjustment to a (-) if necessary. Once the desired adjustment (-35° to 35° F) has been entered, press the START key pad to accept the change or the STOP/CLEAR or CANCEL key pad to reject the change. Electronic Oven Control & Jumper Connections (EOC Rear View)
Resistance Temperature Detector (RTD)
Resistance Temperature Detector Scale
RTD SCALE Temperature (°F) 32 ± 1. 9 75 ± 2. 5 250 ± 4. 4 350 ± 5. 4 450 ± 6. 9 550 ± 8. 2 650 ± 9. 6 900 ± 13. 6 Resistance (ohms) 1000 ± 4. 0 1091 ± 5. 3 1453 ± 8. 9 1654 ± 10. 8 1852 ± 13. 5 2047 ± 15. 8 2237 ± 18. 5 2697 ± 24. 4
Electonic Oven Control Fault Code Descriptions
Fault Code
F10 F11 F12 F13 F20
Likely Failure Condition/Cause
Runaway Temperature. Communication failure between EOC & ESEC system (for electric range models ONLY) Communication failure with Mini Oven Control Board. (for models equipped with Bake-n-WarmTM ONLY) Shorted Probe connection.
Suggested Corrective Action
1. If oven continues to overheat when the power is reapplied, replace EOC. Severe overheating may require the entire oven to be replaced should damage be extensive. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power. Test harness/connections P4 (EOC) & P7 (Surface Element Control Board) 2. [. . . ] If all situations above do not solve probem, replace EOC.
F26
F30 F31
F90 F91 F92 F93 F94 F95
Maximum oven door unlock time exceeded. Door Latch
Circuit Analysis Matrix
IMPORTANT
DO NOT REMOVE THIS BAG OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
p/n 316904401 Rev A (0903)
General Troubleshooting Diagram
General Troubleshooting Schematic [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FRIGIDAIRE ELECTRIC RANGES WITH ES 540
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FRIGIDAIRE ELECTRIC RANGES WITH ES 540 will begin.