User manual FRIEDLAND REPONSE ALARMS SA3

[. . . ] SA3 6 Zone Wirefree Alarm System ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 FIRE TAMPER 1 4 7 2 5 8 0 3 6 9 # ESC ENTER * Installation & Operating Manual FOREWORD All components in this wirefree Alarm System are designed and manufactured to provide a high standard of security protection and long, reliable service. The system is designed for ease of installation using only conventional domestic tools. However, it is essential that the installer reads and fully understands the advice and procedures contained in this manual and plans the system before proceeding with the installation. During installation, it is important that the procedures described in this manual are followed in sequence. [. . . ] Remember that in winter the sun is lower in the sky and you should avoid winter shadows where possible. However, reception of radio signals can be affected by the presence of metallic objects within the vicinity of the Solar Siren. It is therefore important to mount the Solar Siren a minimum distance of 1m away from any external or internal metalwork, (i. e. drainpipes, gutters, radiators, mirrors etc). POSITIONING THE SOLAR SIREN The Siren should be located as high as possible in a prominent position so that it can be easily seen and heard. The Siren should be mounted on a sound flat surface so that the rear tamper switch is not activated when mounted. Ensure that the tamper switch does not fall into the recess between brick courses as this could prevent the switch from closing and give a permanent tamper signal. In order to provide the maximum amount of daylight to the Solar Panel, the siren should ideally be mounted on a south facing wall. Mounting the device on a north facing wall should be avoided as this could mean that during the short dark days of winter months the solar panel may not receive sufficient daylight in order to maintain the battery charge at acceptable levels. NORTH Avoid if possible INSTALLING AND CONFIGURING THE SOLAR SIREN (See diagram overpage). Remove the fixing screw from the bottom edge of the Siren housing and carefully hinge off the front cover. Hold the mounting plate in position and mark the positions of the four mounting holes. Fit the two 30mm fixing screws in the top holes leaving approximately 10mm of the screw protruding. Remove the mounting plate and adjust the screws until they form a neat fit with the mounting plate with minimal movement. Secure the mounting plate in position using the two 25mm fixing screws in the bottom fixing holes. Ensure that the Solar Siren main configuration switch on the LED indicator board is set to "SIREN" for use with this alarm system. Main Configuration Switch (in SIREN Position) C. U. SIREN WEST EAST SOUTH SA3 15 INSTALLATION Ensure that the position selected for the Siren is within effective range of the Control Panel, (refer to "Testing the Control Panel & Remote Control"). Solar Panel Receiver Aerial Tamper switch Front cover locating tabs DIP switch cover P2 P3 P1 ON 1 2 3 4 5 6 7 8 9 7. 5 Volt DC charging adaptor input Beep Disable Link Siren Disable Link Jamming Detection Link 6 Volt 1. 2Ahr rechargeable battery 9 Volt PP3 initial power up battery Main Configuration Switch (in SIREN Position) C. U. SIREN House Code DIP switches 1-8 Alarm duration DIP switch 9 LED Indicator PCB Siren INSTALLATION 7. Undo the 3 screws holding the DIP Switch Cover in place and remove the cover. Note: When the Solar Siren is viewed as shown above (Solar panel at top) the DIP switches are `upside down'. DIP switches 1-8 are used to set the House Code for the Siren and must be set to the same ON/OFF combination as all other system devices. Alarm Duration DIP switch 9 ON to acknowledge signals from the Remote Control, (provided the beep feature is not disabled). To enable the Jamming Detect feature in the Solar Siren fit the jumper link taped to the cover of the Siren control unit across link pins P1 on the circuit board. P1 fitted P1 removed Jamming Detection enabled Jamming Detection disabled 14. Do not over tighten the screw as this could damage the thread. 1 2 3 4 5 6 7 8 9 House Code (Always change from the factory setting) POWER-UP OF THE SOLAR SIREN 1. [. . . ] If there is no additional Magnetic Contact Detector connected ensure jumper link is fitted. Note: If an additional contact is used then the doors/windows protected by both the main wirefree detector and the additional wired detector must be closed when either is opened. If one of the doors/windows is already open then the opening of the other door/window will not be detected. Ensure detector is within effective radio range of Control Panel and is not mounted close to metal objects which may interfere with RF transmission PIR Movement Detector false alarming. 1. [. . . ]